| 전자부품 데이터시트 검색엔진 |
|
STM32H563RI 데이터시트(PDF) 174 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32H563RI 데이터시트(HTML) 174 Page - STMicroelectronics |
|
174 / 270 page ![]() Electrical characteristics STM32H562xx and STM32H563xx 174/270 DS14258 Rev 5 5.3.16 NRST pin characteristics The NRST pin input driver uses CMOS technology. It is connected to a permanent pull-up resistor, RPU (see Table 58). Unless otherwise specified, the parameters in Table 68 are derived from tests performed under the ambient temperature and VDD supply voltage conditions summarized in Table 20. 11 Fmax(2)(4) Maximum frequency C = 50 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 30 MHz C = 40 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 35 C = 30 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 44 C = 20 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 55 C = 10 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 77 tr/tf(3)(4) Output high to low level fall time and output low to high level rise time C = 50 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 11.1 ns C = 40 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 9.2 C = 30 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 7.2 C = 20 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 5.4 C = 10 pF, 1.08 V ≤ VDDIO2 ≤ 1.32 V - 3.6 1. Specified by design - Not tested in production. 2. The maximum frequency is defined with the conditions (tr + tf) ≤ 2/3 T, Skew ≤ 1/20 T, 45%< Duty cycle < 55%. 3. The fall and rise times are defined between 90% and 10% and between 10% and 90% of the output waveform, respectively. 4. Compensation system enabled. Table 66. Output timing characteristics VDDIO2 1.2 V (HSLV ON)(1) (continued) Speed Symbol Parameter Conditions Min Max Unit Table 67. Output timing characteristics for FT_c I/Os (PB13/PB14)(1)(2) Speed Symbol Parameter Conditions Min Max Unit 00 Fmax Maximum frequency C = 50 pF, 2.7 V ≤ VDDIO ≤ 3.6 V - 2 MHz C = 50 pF, 1.71 V ≤ VDDIO < 2.7 V - 1 tr/tf Output rise and fall time C = 50 pF, 2.7 V ≤ VDDIO < 3.6 V - 166 ns C = 50 pF, 1.71 V ≤ VDDIO < 2.7 V - 330 01 Frmax Maximum frequency C = 30 pF, 2.7 V ≤ VDDIO < 3.6 V - 10 MHz C = 30 pF, 1.71 V ≤ VDDIO < 2.7 V - 4 tr/tf Output rise and fall time C = 30 pF, 2.7 V ≤ VDDIO < 3.6 V - 33 ns C = 30 pF, 1.71 V ≤ VDDIO < 2.7 V - 65 1. Specified by design - Not tested in production. 2. The I/O speed is configured using the OSPEEDRy[1:0] bits. Refer to the product reference manual for a description of GPIO port configuration register. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |