ST723217 datasheet(113/185 Pages) STMICROELECTRONICS

113 / 185 page

ST72321

113/185

10.7 I2C BUS INTERFACE (I2C)

10.7.1 Introduction

The I2C Bus Interface serves as an interface be-

tween the microcontroller and the serial I2C bus. It

provides both multimaster and slave functions,

and controls all I2C bus-specific sequencing, pro-

tocol, arbitration and timing. It supports fast I2C

mode (400kHz).

10.7.2 Main Features

Parallel-bus/I2C protocol converter

Multi-master capability

7-bit/10-bit Addressing

Transmitter/Receiver flag

End-of-byte transmission flag

Transfer problem detection

I2C Master Features:

Clock generation

I2C bus busy flag

Arbitration Lost Flag

End of byte transmission flag

Transmitter/Receiver Flag

Start bit detection flag

Start and Stop generation

I2C Slave Features:

Stop bit detection

I2C bus busy flag

Detection of misplaced start or stop condition

Programmable I2C Address detection

Transfer problem detection

End-of-byte transmission flag

Transmitter/Receiver flag

10.7.3 General Description

In addition to receiving and transmitting data, this

interface converts it from serial to parallel format

and vice versa, using either an interrupt or polled

handshake. The interrupts are enabled or disabled

by software. The interface is connected to the I2C

bus by a data pin (SDAI) and by a clock pin (SCLI).

It can be connected both with a standard I2C bus

and a Fast I2C bus. This selection is made by soft-

ware.

Mode Selection

The interface can operate in the four following

modes:

– Slave transmitter/receiver

– Master transmitter/receiver

By default, it operates in slave mode.

The interface automatically switches from slave to

master after it generates a START condition and

from master to slave in case of arbitration loss or a

STOP generation, allowing then Multi-Master ca-

pability.

Communication Flow

In Master mode, it initiates a data transfer and

generates the clock signal. A serial data transfer

always begins with a start condition and ends with

a stop condition. Both start and stop conditions are

generated in master mode by software.

In Slave mode, the interface is capable of recog-

nising its own address (7 or 10-bit), and the Gen-

eral Call address. The General Call address de-

tection may be enabled or disabled by software.

Data and addresses are transferred as 8-bit bytes,

MSB first. The first byte(s) following the start con-

dition contain the address (one in 7-bit mode, two

in 10-bit mode). The address is always transmitted

in Master mode.

A 9th clock pulse follows the 8 clock cycles of a

byte transfer, during which the receiver must send

an acknowledge bit to the transmitter. Refer to Fig-

ure 63.

Figure 63. I2C BUS Protocol

SCL

SDA

MSB

ACK

STOP

START

CONDITION

VR02119B

ST723217 데이터시트(PDF) 113 Page - STMicroelectronics

ST723217 데이터시트(HTML) 113 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL