MPC5633MF0MMGA4 datasheet(117/118 Pages) FREESCALE

117 / 118 page

Document revision history

MPC5634M Microcontroller Data Sheet, Rev. 4

Preliminary—Subject to Change Without Notice

Freescale Semiconductor

117

Rev.4

12/2009

208-pin MAPBGA ballmap for the MPC5633M (1024 KB flash memory) has changed.

Power Management Control (PMC) and Power On Reset (POR) electrical specifications

updated

Temperature sensor data added

Specifications now indicate how each controller characteristic parameter is guaranteed.

I/O pad current specifications updated

I/O Pad VRC33 current specifications updated

PAD AC characteristics updated

VGA gain specifications added to eQADC electrical characteristics

DC electrical specifications updated:

• Footnote added to RPUPD100K and RPUPD200K: When the pull-up and pull-down of

the same nominal 200 K

Ω or 100 KΩ value are both enabled, assuming no interference

from other devices, the resulting pad voltage will be 0.5*VDDE ± 2.5%

•IOL condition added to VOL_LS.

•IOH condition added to VOH_LS.

• Minimum VOH_LS is 2.3 V (was 2.7 V).

• Separate IDDPLL removed from IDD spec because we can only measure IDD +IDDPLL.

IDD increased by 15 mA (to 195 mA) to account for IDDPLL. IDD now documented as

IDD +IDDPLL. Footnote added detailing runtime configuration used to measure

IDD +IDDPLL.

• Specifications for IDDSTBY and IDDSTBY150 reformatted to make more clear.

•VSTBY is now specified by two ranges. The area in between those ranges is

indeterminate.

LVDS pad specifications updated:

• Min value for VOD at SRC=0b01 is 90 mV (was 120); and 160 mV (was 180) at

SRC = 0b10

Changes to Signal Properties table:

• VDDE7 removed as voltage segment from Calibration bus pins. Calibration bus pins

are powered by VDDE12 only.

• GPIO[139] and GPIO[87] pins changed to Medium pads

• Some signal names have changed on 176-pin QFP package pinout: “CAL_x” signals

renamed to “ALT_x”.

Changes to Pad Types table:

• Column heading changed from “Voltage” to “Supply Voltage”

• MultiV pad high swing mode voltage changed to 3.0 V – 5.25 V (was 4.5 V – 5.25 V)

• MultiV pad low swing mode voltage changed to 4.5 V – 5.25 V (was 3.0 V – 3.6 V)

Signal details table added

Power/ground segmentation table added

100-pin package is no longer available

Table 42. Revision history (continued)

Revision

Date

Substantive changes

MPC5633MF0MMGA4 데이터시트(PDF) 117 Page - Freescale Semiconductor, Inc

MPC5633MF0MMGA4 데이터시트(HTML) 117 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL