PIC18F4580-ESLASHML datasheet(149/490 Pages) MICROCHIP

149 / 490 page

DS39637D-page 149

PIC18F2480/2580/4480/4580

11.6

Parallel Slave Port

In addition to its function as a general I/O port, PORTD

can also operate as an 8-bit wide Parallel Slave Port

(PSP) or microprocessor port. PSP operation is con-

trolled by the 4 upper bits of the TRISE register

(Register 11-1).

Setting

control

bit,

PSPMODE

(TRISE<4>), enables PSP operation, as long as the

Enhanced CCP module is not operating in dual output

or quad output PWM mode. In Slave mode, the port is

asynchronously readable and writable by the external

world.

The PSP can directly interface to an 8-bit micro-

processor data bus. The external microprocessor can

read or write the PORTD latch as an 8-bit latch. Setting

the control bit PSPMODE enables the PORTE I/O pins

to become control inputs for the microprocessor port.

When set, port pin RE0 is the RD input, RE1 is the WR

input and RE2 is the CS (Chip Select) input. For this

functionality, the corresponding data direction bits of

the TRISE register (TRISE<2:0>) must be configured

as inputs (set). The A/D port Configuration bits,

PFCG<3:0> (ADCON1<3:0>), must also be set to

‘1010’.

A write to the PSP occurs when both the CS and WR

lines are first detected low and ends when either are

detected high. The PSPIF and IBF flag bits are both set

when the write ends.

A read from the PSP occurs when both the CS and RD

lines are first detected low. The data in PORTD is read

out and the OBF bit is set. If the user writes new data

to PORTD to set OBF, the data is immediately read out;

however, the OBF bit is not set.

When either the CS or RD lines are detected high, the

PORTD pins return to the input state and the PSPIF bit

is set. User applications should wait for PSPIF to be set

before servicing the PSP; when this happens, the IBF

and OBF bits can be polled and the appropriate action

taken.

The timing for the control signals in Write and Read

modes is shown in Figure 11-3 and Figure 11-4,

respectively.

FIGURE 11-2:

PORTD AND PORTE

BLOCK DIAGRAM

(PARALLEL SLAVE PORT)

Note:

The Parallel Slave Port is only available on

PIC18F4X80 devices.

Data Bus

WR LATD

RDx pin

RD PORTD

One bit of PORTD

Set Interrupt Flag

PSPIF (PIR1<7>)

Read

Chip Select

Write

TTL

WR PORTD

RD LATD

Data Latch

Note:

I/O pins have diode protection to VDD and VSS.

PORTE Pins

PIC18F4580-E/ML 데이터시트(PDF) 149 Page - Microchip Technology

PIC18F4580-E/ML 데이터시트(HTML) 149 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL