AT90PWM2 datasheet(300/361 Pages) ATMEL

300 / 361 page

300

4317J–AVR–08/10

AT90PWM2/3/2B/3B

Note:

1. “Max” means the highest value where the pin is guaranteed to be read as low

2. “Min” means the lowest value where the pin is guaranteed to be read as high

3. Although each I/O port can sink more than the test conditions (20 mA at V

CC = 5V, 10 mA at VCC = 3V) under steady state

conditions (non-transient), the following must be observed:

SO32, SO24 and TQFN Package:

1] The sum of all IOL, for all ports, should not exceed 400 mA.

2] The sum of all IOL, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 100 mA.

3] The sum of all IOL, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 100 mA.

4] The sum of all IOL, for ports B3 - B5, C6 - C7 should not exceed 100 mA.

5] The sum of all IOL, for ports B2, C4 - C5, D5 - D7 should not exceed 100 mA.

If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test condition.

4. Although each I/O port can source more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state

conditions (non-transient), the following must be observed:

SO32, SO24 and TQFN Package:

1] The sum of all IOH, for all ports, should not exceed 400 mA.

2] The sum of all IOH, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 150 mA.

3] The sum of all IOH, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 150 mA.

4] The sum of all IOH, for ports B3 - B5, C6 - C7 should not exceed 150 mA.

5] The sum of all IOH, for ports B2, C4 - C5, D5 - D7 should not exceed 150 mA.

If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current

greater than the listed test condition.

ICC

Power Supply Current

Active 8 MHz, VCC = 3V,

RC osc, PRR = 0xFF

3.8

Active 16 MHz, VCC = 5V,

Ext Clock, PRR = 0xFF

Idle 8 MHz, VCC = 3V, RC

Osc

1.5

Idle 16 MHz, VCC = 5V,

Ext Clock

5.5

Power-down mode(5)

WDT enabled, VCC = 3V

t0 < 90°C

515

µA

WDT enabled, VCC = 3V

t0 < 105°C

920

µA

WDT disabled, VCC = 3V

t0 < 90°C

µA

WDT disabled, VCC = 3V

t0 < 105°C

510

µA

VACIO

Analog Comparator

Input Offset Voltage

AT90PWM2/3

VCC = 5V, Vin = 3V

Vhysr

Analog Comparator

Hysteresis Voltage

AT90PWM2B/3B

VCC = 5V, Vin = 3V

Rising Edge

Falling Edge

110

IACLK

Analog Comparator

Input Leakage Current

VCC = 5V

Vin = VCC/2

-50

tACID

Analog Comparator

Propagation Delay

VCC = 2.7V

VCC = 5.0V

(6)

A = -40°C to +105°C, VCC = 2.7V to 5.5V (unless otherwise noted) (Continued)

Symbol

Parameter

Condition

Min.

Typ.

Max.

Units

AT90PWM2 데이터시트(PDF) 300 Page - ATMEL Corporation

AT90PWM2 데이터시트(HTML) 300 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL