| 전자부품 데이터시트 검색엔진 |
|
41594B 데이터시트(PDF) 337 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
41594B 데이터시트(HTML) 337 Page - Microchip Technology |
|
337 / 372 page ![]() 2011-2012 Microchip Technology Inc. Preliminary DS41594B-page 337 PIC12LF1840T48A TABLE 31-5: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET PARAMETERS Standard Operating Conditions (unless otherwise stated) Operating Temperature -40°C TA +125°C Param No. Sym. Characteristic Min. Typ† Max. Units Conditions 30 TMCLMCLR Pulse Width (low) 2 5 — — — — s s VDD = 3.3-5V, -40°C to +85°C VDD = 3.3-5V 31 TWDTLP Watchdog Timer Time-out Period 10 16 27 ms VDD = 3.3V-5V, 1:16 Prescaler used 32 TOST Oscillator Start-up Timer Period(1), (2) — 1024 — Tosc (Note 3) 33* TPWRT Power-up Timer Period, PWRTE = 0 40 65 140 ms 34* TIOZ I/O high-impedance from MCLR Low or Watchdog Timer Reset —— 2.0 s 35 VBOR Brown-out Reset Voltage 2.6 1.80 2.7 1.9 2.85 2.05 VBORV=2.7V PIC12LF1840T48A BORV=1.9V 37* VHYST Brown-out Reset Hysteresis 0 25 50 mV -40°C to +85°C 38* TBORDC Brown-out Reset DC Response Time 01 40 sVDD VBOR * These parameters are characterized but not tested. † Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “min” values with an external clock applied to the OSC1 pin. When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices. 2: By design. 3: Period of the slower clock. 4: To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 F and 0.01 F values in parallel are recommended. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |