| 전자부품 데이터시트 검색엔진 |
|
HT85F2270 데이터시트(PDF) 155 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT85F2270 데이터시트(HTML) 155 Page - Holtek Semiconductor Inc |
|
155 / 226 page ![]() Rev. 1.00 1�� of ��6 �a� 1�� �01� Standard 8051 8-Bit Flash MCU HT85F2260/HT85F2270/HT85F2280 ADCR0 Register SFR Address: F1h Bit 7 6 5 4 3 2 1 0 Name START EOCB ADOFF ADRFS ACS� ACS� ACS1 ACS0 R/W R/W R R/W R/W R/W R/W R/W R/W POR 0 1 1 0 0 0 0 0 Bit 7 START: Starts the A/D conversion 0→1→0: Start 0→1: Reset the A/D converter and set EOCB to “1” This bit is used to initiate an A/D conversion process. The bit is normally low but if set high and then cleared low again, the A/D converter will initiate a conversion process. When the bit is set high the A/D converter will be reset. Bit 6 EOCB: End of A/D conversion flag 0: A/D conversion ended 1: A/D conversion in progress This read only flag is used to indicate when an A/D conversion process has completed. When the conversion process is running the bit will be high. Bit 5 ADOFF : ADC power on/off control bit 0: ADC power on 1: ADC power off This bit controls the power to the A/D internal function. This bit should be cleared to zero to enable the A/D converter. If the bit is set high then the A/D converter will be switched off reducing the device power consumption. As the A/D converter will consume a limited amount of power, even when not executing a conversion, this may be an important consideration in power sensitive battery powered applications. Bit 4 ADRFS: ADC Data Format Control 0: ADC Data MSB is ADRH bit 7, LSB is ADRL bit 4 1: ADC Data MSB is ADRH bit 3, LSB is ADRL bit 0 This bit controls the format of the 12-bit converted A/D value in the two A/D data registers. Bit 3~0 ACS3~ACS0: Select A/D channel (when ACS4 is “0”) 0000: AIN.0 0001: AIN.1 0010: AIN.2 0011: AIN.3 0100: AIN.4 0101: AIN.5 0110: AIN.6 0111: AIN.7 1xxx: Undefined, must not be used These are the A/D channel select control bits. As there is only one internal hardware A/D converter each of the eight A/D inputs must be routed to the internal converter using these bits. If bit ACS4 in the ADCR1 register is set high then the internal temperature sensor will be routed to the A/D Converter and these ADC input channels disconnected. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |