DSPIC33FJMC202ESS datasheet(245/330 Pages) MICROCHIP

245 / 330 page

DS70283K-page 245

dsPIC33FJ32MC202/204 and dsPIC33FJ16MC304

FIGURE 24-2:

EXTERNAL CLOCK TIMING

OSC1

CLKO

OS20

OS25

OS30

OS40

OS41

OS31

TABLE 24-16: EXTERNAL CLOCK TIMING REQUIREMENTS

AC CHARACTERISTICS

Standard Operating Conditions: 3.0V to 3.6V

(unless otherwise stated)

Operating temperature

-40°C

≤TA ≤+85°C for Industrial

-40°C

≤TA ≤+125°C for Extended

Param

No.

Symb

Characteristic

Min

Typ(1)

Max

Units

Conditions

OS10

FIN

External CLKI Frequency(4)

(External clocks allowed only

in EC and ECPLL modes)

—

MHz

Oscillator Crystal Frequency(5)

3.5

—

MHz

kHz

Sosc

OS20

TOSC

TOSC = 1/FOSC(4)

12.5

—

OS25

TCY

Instruction Cycle Time(2,4)

—

OS30

TosL,

TosH

External Clock in (OSC1)(5)

High or Low Time

0.375 x TOSC

—

0.625 x TOSC

OS31

TosR,

TosF

External Clock in (OSC1)(5)

Rise or Fall Time

——

OS40

TckR

CLKO Rise Time(3,5)

—5.2

—

OS41

TckF

CLKO Fall Time(3,5)

—5.2

—

OS42

External Oscillator

Transconductance(6)

mA/V VDD = 3.3V

TA = +25ºC

Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.

2: Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values

are based on characterization data for that particular oscillator type under standard operating conditions

with the device executing code. Exceeding these specified limits may result in an unstable oscillator

operation and/or higher than expected current consumption. All devices are tested to operate at “min.”

values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the

“max.” cycle time limit is “DC” (no clock) for all devices.

3: Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.

4: These parameters are characterized by similarity, but are tested in manufacturing at FIN = 40 MHz only.

5: These parameters are characterized by similarity, but are not tested in manufacturing.

6: Data for this parameter is preliminary. This parameter is characterized, but is not tested in manufacturing.

DSPIC33FJMC202ESS 데이터시트(PDF) 245 Page - Microchip Technology

DSPIC33FJMC202ESS 데이터시트(HTML) 245 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL