OMAP3530ECBBA datasheet(156/265 Pages) TI1

156 / 265 page

OMAP3530, OMAP3525

SPRS507H – FEBRUARY 2008 – REVISED OCTOBER 2013

www.ti.com

6.4

External Memory Interfaces

The OMAP3530/25 processor includes the following external memory interfaces:

•

General-purpose memory controller (GPMC)

•

SDRAM controller (SDRC)

6.4.1

General-Purpose Memory Controller (GPMC)

The GPMC is the OMAP3530/25 unified memory controller used to interface external memory devices

such as:

•

Asynchronous SRAM-like memories and ASIC devices

•

Asynchronous page mode and synchronous burst NOR flash

•

NAND flash

6.4.1.1

GPMC/NOR Flash Interface Synchronous Timing

Table 6-3 and Table 6-4 assume testing over the recommended operating conditions (see Figure 6-2

through Figure 6-5) and electrical characteristic conditions.

Table 6-2. GPMC/NOR Flash Synchronous Mode Timing Conditions

TIMING CONDITION PARAMETER

VALUE

UNIT

Input Conditions

Input signal rise time

1.8

Input signal fall time

1.8

Output Conditions

CLOAD

Output load capacitance

15.94

Table 6-3. GPMC/NOR Flash Interface Timing Requirements – Synchronous Mode(1)

NO.

PARAMETER

OPP3

OPP2

OPP1(2)

UNIT

MIN

MAX

MIN

MAX

MIN

MAX

F12

tsu(DV-CLKH)

Setup time, read gpmc_d[15:0]

1.9

3.2

valid before gpmc_clk high

F13

th(CLKH-DV)

Hold time, read gpmc_d[15:0]

1.9

valid after gpmc_clk high

F21

tsu(WAITV-CLKH)

Setup time, gpmc_waitx(3) valid

1.9

3.2

before gpmc_clk high

F22

th(CLKH-WAITV)

Hold Time, gpmc_waitx(3) valid

2.5

after gpmc_clk high

(1)

For VDD2 (vdd_core) OPP voltages, see Section 3.3, Recommended Operating Conditions.

(2)

Cannot boot in OPP1. If OPP1 is desired, boot in higher OPP then switch to OPP1.

(3)

Wait monitoring support is limited to a WaitMonitoringTime value > 0. For a full description of wait monitoring feature, see the OMAP35x

Technical Reference Manual (literature number SPRUF988).

Table 6-4. GPMC/NOR Flash Interface Switching Characteristics – Synchronous Mode

NO.

PARAMETER

1.15 V

1.0 V

0.9 V

UNIT

MIN

MAX

MIN

MAX

MIN

MAX

tc(CLK)

Cycle time(15), output

12.05

clock gpmc_clk period

tw(CLKH)

Typical pulse duration,

0.5 P(12)

output clock gpmc_clk

high

tw(CLKL)

Typical pulse duration,

0.5 P(12)

output clock gpmc_clk low

tdc(CLK)

Duty cycle error, output

–500

500

–602

602

–1250

1250

clk gpmc_clk

156

TIMING REQUIREMENTS AND SWITCHING CHARACTERISTICS

Submit Documentation Feedback

Product Folder Links: OMAP3530 OMAP3525

OMAP3530ECBBA 데이터시트(PDF) 156 Page - Texas Instruments

OMAP3530ECBBA 데이터시트(HTML) 156 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL