EM357-RTR datasheet(176/241 Pages) SILABS

176 / 241 page

Rev 1.3

176

10.1.5.2. Input Range

The single-ended input range is fixed as 0 V to VREF and the differential input range is fixed as -VREF to +VREF.

10.1.5.3. Sample Time

ADC sample time is programmed by selecting the sampling clock and the clocks per sample.



The sampling clock may be either 1 MHz or 6 MHz. If the ADC_1MHZCLK bit in the ADC_CFG register is

clear, the 6 MHz clock is used; if it is set, the 1 MHz clock is selected. The 6 MHz sample clock offers faster

conversion times but the ADC resolution is lower than that achieved with the 1 MHz clock.



The number of clocks per sample is determined by the ADC_PERIOD bits in the ADC_CFG register.

ADC_PERIOD values select from 32 to 4096 sampling clocks in powers of two. Longer sample times

produce more significant bits. Regardless of the sample time, converted samples are always 16-bits in size

with the significant bits left-aligned within the value.

Table 10.4 shows the options for ADC sample times and the significant bits in the conversion results.

10.2. Interrupts

The ADC has its own top-level interrupt in the NVIC. The ADC interrupt is enabled by writing the INT_ADC bit to

the INT_CFGSET register, and cleared by writing the INT_ADC bit to the INT_CFGCLR register. "11. Interrupt

System" on page 190, describes the interrupt system in detail.

Five kinds of ADC events can generate an ADC interrupt, and each has a bit flag in the INT_ADCFLAG register to

identify the reason(s) for the interrupt:



INT_ADCOVF – an ADC conversion result was ready but the DMA was disabled (DMA buffer overflow).



INT_ADCSAT– the gain correction multiplication exceeded the limits for a signed 16-bit number (gain

saturation).



INT_ADCULDFULL – the DMA wrote to the last location in the buffer (DMA buffer full).



INT_ADCULDHALF – the DMA wrote to the last location of the first half of the DMA buffer (DMA buffer half

full).



INT_ADCDATA – there is data ready in the ADC_DATA register.

Table 10.4. ADC Sample Times*

ADC_PERIOD

Sample

Clocks

Sample Time (µs)

Sample Frequency (kHz)

Significant

Bits

1 MHz Clock

6 MHz Clock

1 MHz Clock

6 MHz Clock

5.33

31.3

188

10.7

15.6

93.8

128

21.3

7.81

46.9

256

42.7

3.91

23.4

512

85.3

1.95

11.7

1024

170

0.977

5.86

2048

341

0.488

2.93

4096

682

0.244

1.47

*Note:

ADC sample timing is the same whether the EM35x is using the 24 MHz crystal oscillator or the 12 MHz high-speed

RC oscillator. This facilitates using the ADC soon after the CPU wakes from deep sleep, before switching to the crystal

oscillator.

EM357-RTR 데이터시트(PDF) 176 Page - Silicon Laboratories

EM357-RTR 데이터시트(HTML) 176 Page - Silicon Laboratories

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL