TNETV2664FIBZWT datasheet(152/249 Pages) TI1

152 / 249 page

TMS320C6424

SPRS347D – MARCH 2007 – REVISED DECEMBER 2009

www.ti.com

6.5.1.2

Latching Boot and Configuration Pins

Internal to the chip, the two device reset pins RESET and POR are logically AND’d together only for the

purpose of latching device boot and configuration pins. The values on all device and boot configuration

pins are latched into the BOOTCFG register when the logical AND of RESET and POR transitions from

low-to-high.

6.5.2

Warm Reset (RESET Pin)

A Warm Reset is activated by driving the RESET pin active low. This resets everything in the device

except the emulation logic. An emulator session will stay alive during warm reset.

For more information on POR vs. RESET usage, see Section 6.5.1.1, Usage of POR versus RESET Pins

and Section 6.5.1.2, Latching Boot and Configuration Pins.

The following sequence must be followed during a Warm Reset:

1. Power supplies and input clock source should already be stable.

2. The RESET pin must be asserted (low) for a minimum of 12 MXI cycles.

Within the low period of the RESET pin, the following happens:

–

The reset signals flow to the entire chip resetting all the modules on chip, except the emulation

logic.

–

The PLL Controllers are reset thereby, switching back to PLL Bypass Mode and resetting all their

registers to default values. Both PLL1 and PLL2 are placed in reset and lose lock.

–

The RESETOUT pin becomes asserted (low), indicating the device is in reset.

3. The RESET pin may now be deasserted (driven high).

When the RESET pin is deasserted (high), the configuration pin values are latched and the PLL

Controllers changed their system clocks to their default divide-down values. Both PLL Controllers are

still in PLL Bypass Mode. Other device initialization also begins.

4. After device initialization is complete, the PLL Controllers pause the system clocks for 10 cycles. At the

end of these 10 cycles, the RESETOUT pin is deasserted (driven high).

At this point:

–

The I/O pins are controlled by the default peripherals (default peripherals are determined by

PINMUX0 and PINMUX1 registers).

–

The clock and reset of each peripheral is determined by the default settings of the Power and Sleep

Controller (PSC).

–

The PLL Controllers are operating in PLL Bypass Mode.

–

The C64x+ begins executing from DSPBOOTADDR (determined by bootmode selection).

After the reset sequence, the boot sequence begins. For more details on the boot sequence, see the

Using the TMS320C642x Bootloader Application Report (literature number SPRAAK5).

After the boot sequence, follow the software initialization sequence described in Section 3.8, Device

Initialization Sequence After Reset.

6.5.3

Maximum Reset

A Maximum (Max) Reset is initiated by the emulator or the watchdog timer (Timer 2). The effects are the

same as a warm reset, except the device boot and configuration pins are not re-latched. The emulator

initiates a maximum reset via the ICEPICK module. This ICEPICK initiated reset is non-maskable. When

the watchdog timer counter reaches zero, this will also initiate a maximum reset to recover from a runaway

condition. The watchdog timeout reset condition is masked if the TIMERCTL.WDRST bit is cleared to "0".

To invoke the maximum reset via the ICEPICK module, the user can perform the following from the Code

Composer Studio™ IDE menu: Debug

→ Advanced Resets → System Reset

This is the Max Reset sequence:

152

Peripheral Information and Electrical Specifications

Submit Documentation Feedback

Product Folder Link(s): TMS320C6424

TNETV2664FIBZWT 데이터시트(PDF) 152 Page - Texas Instruments

TNETV2664FIBZWT 데이터시트(HTML) 152 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL