|
1 Introduction
The i.MX 6SoloLite processor represents the latest
achievement in integrated multimedia applications
processors, which are part of a growing family of
multimedia-focused products that offer high
performance processing and are optimized for lowest
power consumption.
The processor features NXP’s advanced implementation
of the a single ARM® Cortex®-A9 MPCore™ multicore
processor, which operates at speeds up to 1 GHz. It
includes 2D graphics processor and integrated power
management. The processor provides a 32-bit
DDR3-800 memory interface and a number of other
interfaces for connecting peripherals, such as WLAN,
Bluetooth™, GPS, hard drive, displays, and camera
sensors.
The i.MX 6SoloLite processor is specifically useful for
applications, such as:
• Color and monochrome eReaders
• Entry level tablets
• Barcode scanners
1.2 Features
The i.MX 6SoloLite processor is based on ARM Cortex-A9 MPCore multicore processor, which has the
following features:
• ARM Cortex-A9 MPCore CPU processor (with TrustZone)
• The core configuration is symmetric, where each core includes:
— 32 KByte L1 Instruction Cache
— 32 KByte L1 Data Cache
— Private Timer and Watchdog
— Cortex-A9 NEON MPE (Media Processing Engine) co-processor
The ARM Cortex-A9 MPCore complex includes:
• General Interrupt Controller (GIC) with 128 interrupt support
• Global Timer
• Snoop Control Unit (SCU)
• 256 KB unified I/D L2 cache
• Two Master AXI (64-bit) bus interfaces output of L2 cache
• Frequency of the core (including NEON and L1 cache) as per Table 9, "Operating Ranges," on
page 20
• NEON MPE coprocessor
— SIMD Media Processing Architecture
— NEON register file with 32x64-bit general-purpose registers
— NEON Integer execute pipeline (ALU, Shift, MAC)
— NEON dual, single-precision floating point execute pipeline (FADD, FMUL)
— NEON load/store and permute pipeline
The SoC-level memory system consists of the following additional components:
— Boot ROM, including HAB (96 KB)
— Internal multimedia / shared, fast access RAM (OCRAM, 128 KB)
• External memory interfaces:
— 16-bit, and 32-bit DDR3-800, and LPDDR2-800 channels
— 16/32-bit NOR Flash.
— 16/32-bit PSRAM, Cellular RAM (32 bits or less)
Each i.MX 6SoloLite processor enables the following interfaces to external devices (some of them are
muxed and not available simultaneously):
• Displays—Total of three interfaces are available.
— LCD, 24-bit display port, up to 225 Mpixels/sec (for example, WUXGA at 60 Hz)
— EPDC, color, and monochrome E Ink, up to 1650 x 2332 resolution and 5-bit grayscale
• Camera sensors:
— Parallel Camera port (up to 16-bit and up to 66 MHz peak)
• Expansion cards:
— Four MMC/SD/SDIO card ports all supporting:
– 1-bit or 4-bit transfer mode specifications for SD and SDIO cards up to UHS-I SDR-104
mode (104 MB/s max)
– 1-bit, 4-bit, or 8-bit transfer mode specifications for MMC cards up to 52 MHz in both SDR
and DDR modes (104 MB/s max)
– 4-bit or 8-bit transfer mode specifications for eMMC chips up to 200 MHz in HS200 mode
(200 MB/s max)
• USB:
— Two High Speed (HS) USB 2.0 OTG (Up to 480 Mbps), with integrated HS USB Phy
— One USB 2.0 (480 Mbps) hosts:
– One HS hosts with integrated HS-IC USB (High Speed Inter-Chip USB) Phy
• Miscellaneous IPs and interfaces:
— SSI block—capable of supporting audio sample frequencies up to 192 kHz stereo inputs and
outputs with I2S mode
— Five UARTs, up to 5.0 Mbps each:
– Providing RS232 interface
– Supporting 9-bit RS485 multidrop mode
– One of the five UARTs (UART1) supports 8-wire while others four supports 4-wire. This is
due to the SoC IOMUX limitation, since all UART IPs are identical.
— Four eCSPI (Enhanced CSPI)
— Three I2C, supporting 400 kbps
— Ethernet Controller, 10/100 Mbps
— Four Pulse Width Modulators (PWM)
— System JTAG Controller (SJC)
— GPIO with interrupt capabilities
— 8x8 Key Pad Port (KPP)
— Sony Philips Digital Interface (SPDIF), Rx and Tx
— Two Watchdog timers (WDOG)
— Audio MUX (AUDMUX)
The i.MX 6SoloLite processor integrates advanced power management unit and controllers:
• Provide PMU, including LDO supplies, for on-chip resources
• Use Temperature Sensor for monitoring the die temperature
• Support DVFS techniques for low power modes
• Use Software State Retention and Power Gating for ARM and MPE
• Support various levels of system power modes
• Use flexible clock gating control scheme
|