|
FEATURES
• Wide gain range: 0 to 60dB in 3dB steps
• Wide supply range: ±5V to ±17V
• Wide output swing: +27dBu (±17V sup.)
• Wide input swing: +27dBu (±17V sup.)
• Low THD+N: <0.001% @ 1kHz,
up to 42dB gain
• Integrated differential servo minimizes
output offset
• Zero-crossing detector minimizes
switching noise
• Daisy Chainable SPI interface
• Four general-purpose digital outputs
• Small 5mm x 5mm QFN24 package
APPLICATIONS
• Digitally controlled microphone
preamplifiers
• Digitally controlled instrumentation
amplifiers
• Digitally controlled differential
amplifiers
• Audio mixing Consoles
• PC audio breakout boxes
• Audio distribution systems
• Digital audio snakes
• Portable audio recorders
Description
The THAT5173 is a digital gain controller for
low-noise, analog, differential, current-feedback
audio preamplifiers such as the THAT 1580 and
1583. When used in conjunction with an appropriate
analog gain block, the 5173 supports digitally
controlled gain from 0dB to 60dB in 3dB steps, while
preserving low noise and distortion. It operates from
±5V to ±17V analog supplies, supporting input
signal levels as high as +27 dBu (at 0dB gain and
±17V supplies) in combination with the 1580 or
1583 -- without an input pad. The 5173 includes a
differential servo and zero-crossing detector to
minimize dc offsets and glitches (zipper noise) during
gain adjustments.
The 5173 is controlled via an industry standard
serial-peripheral interface (SPI) port. Four
G e neral Purpose Outputs (GPOs) can be controlled
via this interface. The GPOs may be used to control
auxiliary functions such as input selectors, filters,
mutes, LEDs, relays, etc.
The 5173 was designed to mate perfectly with the
THAT 1580 and 1583 Differential Audio Preamplifier
ICs. Together, these combinations provide a high
performance solution for digitally-controllable audio
preamplifier applications. However, the 5173 may
also be used to control a discrete preamplifier.
Fabricated in a high-voltage CMOS process, the
5173 integrates an astonishing amount of circuitry
within a very small package. It comes in a small (5x5
mm) 24-pin QFN package, making it suitable for
small portable devices.
Applications
While the 5173 is perfectly suitable for application to virtually any discrete current-feedback differential preamplifier, the applications discussed herein are exclusively based on use with the companion THAT158X IC. The circuit of Figure 9 shows the most basic application of the 5173 and 158X to form a complete low-noise digitally-controlled microphone preamplifier.
Gain Ranges in Basic Configurations
The circuit of Figure 9 offers differential gain that varies from 0 to 60dB in 3dB steps. For single-ended analog outputs, the circuit of Figure 9 can be followed by a differential-to-single-ended converter, as shown in Figure 10.
At minimum gain (0dB) and with ±15V supply rails, the maximum (differential) input signal level is +26.8dBu, and the maximum (differential) output signal level is +26.6dBu. At maximum gain (+60dB), the maximum input signal level is -33dBu, and the maximum output signal level remains +26.6dBu. All these figures increase by a little over 1dB if the circuit is run from ±17V supplies.
When converting to single-ended signals, take care to select a low-noise opamp, and pay attention to the noise generated by the impedances. The component values shown in Figure 10 will largely preserve the dynamic range of the 158X and 5173 combination.
For many applications, the output of the microphone preamplifier must drive an analog-to-digital converter. Most high-performance A/D converters have differential inputs, and cannot accept differential signals greater than ~+8dBu. For such applications, the output of the mic preamp must be attenuated to prevent overload of the A/D converter. The circuit of Figure 11 shows one typical circuit, using a simple resistive attenuator (R9 through R11). The impedance levels of the attenuator are chosen to minimize their self-generated voltage noise, and to stay within the load limits of the amplifier which drives them. Figure 11 assumes that the maximum differential input to the A/D converter is +8dBu. For higher (or lower) maximum input levels, or for different supply voltages to the 158X and 5173, scale the attenuator accordingly, keeping its total impedance (R9 + R10 + R11) the same. Please note that the noise contribution of the U-pad can compromise the theoretical noise performance of the 158X/5173 combination at minimum gain. Moreover, the non-zero impedance drive to the converter may increase distortion with high-performance converters. The impact of this impedance depends on the ADC.
Note that one drawback of the circuit shown in Figure 11 is that it offers no attenuation of common-signals. The 158X has unity common-mode gain regardless of its differential gain. When set to unity gain, the circuit of Figure 9 has 0dB CMRR. The U-pad attenuator formed by R9~R11 attenuates differential
|