전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

NPIS104F680MTRF 데이터시트(PDF) 3 Page - Diodes Incorporated

부품명 NPIS104F680MTRF
상세설명  The evaluation board does not have reverse supply protection
PDF  8 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  DIODES [Diodes Incorporated]
홈페이지  http://www.diodes.com
Logo DIODES - Diodes Incorporated

NPIS104F680MTRF 데이터시트(HTML) 3 Page - Diodes Incorporated

  NPIS104F680MTRF Datasheet HTML 1Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 2Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 3Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 4Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 5Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 6Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 7Page - Diodes Incorporated NPIS104F680MTRF Datasheet HTML 8Page - Diodes Incorporated  
Zoom Inzoom in Zoom Outzoom out
 3 / 8 page
background image
AL8807EV3
Issue 1 – December 2011
www.diodes.com
© Diodes Incorporated 2011
3
ORDERING INFORMATION
EVALBOARD ORDER
NUMBER
AL8807EV3
Please note: Evaluation boards are subject to
availability and qualified sales leads.
DEVICE ORDER NUMBER
AL8807MP-13
AL8807EV3 EVALUATION BOARD REFERENCE DESIGN
The AL8807EV3 is configured to the reference design in Figure 2.
The operating voltage is up to 36V. The nominal current is set at 1A with a 0R1 sense resistor R1.
The circuit operates in continuous mode between approximately 40kHz and 130kHz, depending on
the input voltage, and with a 68uH inductor and one LED.
Both DC and PWM dimming can be achieved by driving the CTRL pin. For DC dimming, the CTRL pin
may be driven between 0.5V and 2.5V adjusting the output current from 25% to 100% of ILED.
Driving the CTRL pin below 0.4V will shut down the output current.
A PWM signal (low level ≤ 0.4V and high level > 2.5) allows the output current to be adjusted above or
below the level set by the resistor connected to SET input pin. The PWM frequency can be around
100Hz to 1kHz, providing a resolution of 10 bits.
For low frequency PWM, C2 should be removed from the evaluation board, to give a more accurate
duty cycle .
Shorting R2 will connect the test pin CTRL to device pin CTRL, if required.
For other reference designs or further applications information, please refer to the AL8807 datasheet.
Figure 2: Schematic diagram



Html Pages

1 2 3 4 5 6 7 8


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com