1177 East Tower Road, Schaumburg, IL 60173

Tel: 847-884-6664

Fax: 847-884-6665

E-mail: sales@tocos.com

www.tocos.com

Specifications

Electrical

Standard Resistance Range . . . . . . . . . . . . . 1k

Ω to 100kΩ

Resistance Tolerance . . . . . . . . . . . . . . . . .

20% standard

End Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Ω max.

Resistance Taper . . . . . . . . . . . . . . . . . . . . . . . . . . B = linear

Peak Noise (C.R.V.) . . . . . . . . . . . . . . . . . . . . . . 100mV max.

Power Rating . . . . . . . . 0.05 watt at

50 C, 0 watt at

70 C

Maximum Input Voltage . . . . . . . . . 70VDC or power rating,

whichever is smaller

Insulation Resistance . . . . . . . 100M

Ω minimum at 250VDC

Dielectric Strength . . . . . . . . . . . . . . . . . . 300VAC, 1 minute

Adjustment Travel . . . . . . . . . . . . . . . . . . . . . . 266 nominal

Mechanical

Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . . 300

5

Shaft Strength (push) . . . . . . . . . . . . . . 98.1 N (10 kgf ) min.

Shaft Strength (tensile) . . . . . . . . . . . . . 98.1 N (10 kgf ) min.

Shaft End Play . . . . . . . .

0.5

(shaft length /30) mm max.

Marking . . . . . . . . . . . . . Model type, taper, resistance code,

terminal identification, date code

Environmental

Temperature Range . . . . . . . . . . . . . . . . . .

20 Cto

70 C

Temperature Characteristics . . . . . . . . .

70 C, 240 hours

∆T/R ) 5%, 30%

Temperature Cycle . . . . . . . . . . . . . . . . . . . .

20 C, 70 C,

30 minutes each, 5 cycles

∆T/R ) 10%, 30%

Load Life . . . . . . . . . . . . . . . .

50 C, 0.05 watt, 1,000 hours

∆T/R ) 30%

Moisture and Load Life . . . . . . . . . . . .

40 C, 90-95%RH,

0.05 watt, 350 hours

∆T/R ) 20%

Vibration . . . . . . . . .10-55Hz, 1.5mm amplitude, 3 directions

∆T/R ) 2.5%

Soldering Heat Resistance . . . . . . . 350 C

5 C, 5 seconds

∆T/R ) 5%

Rotational Life . . . . . . . . . . . 300,000 cycles with 3.5V load

∆T/R ) 15%

∆T/R = Total Resistance Change

Long Life 9mm Square, Single-Turn, Carbon Panel Controls

P ANEL CONTROLS

Features

Long life 9mm square, single-turn industrial panel controls

Carbon film element

Up to 300,000 cycle rotational life

Single unit, single shaft

Internal resin molded coating to prevent flux intrusion

Metal shaft and bushing

Linear taper

Standard 15mm or 20mm shaft length

6mm diameter shafts in slot, flat or round end styles

Standard PCB right angle inline pin terminals

Vertical mount pin terminals available as special order

Note: A long life panel control should only be used in a circuit

as a potentiometer (3-terminal voltage divider ).

Unit: mm

84

TP96N93

TP96N238