EMC6D103 datasheet(69/89 Pages) SMSC

69 / 89 page

Fan Control Device with High Frequency PWM Support and Hardware Monitoring Features

Datasheet

SMSC EMC6D103

Revision 0.4 (04-04-05)

DATASHEET

Note: The range numbers will be used to calculate the slope of the PWM ramp up. For the fractional

entries, the PWM will go on full when the temp reaches the next integer value e.g., for 3.33,

PWM will be full on at (min. temp + 4).

8.2.17

These registers become read only when the Lock bit is set. Any further attempts to write to these

registers shall have no effect.

The duty cycle will be set to the Minimum Fan Duty Cycle when the measured temperature falls below

the Temperature LIMIT register setting for the corresponding PWM.

Description of Ramp Rate Control bits:

If the Remote1 or Remote2 pins are connected to a processor or chipset, instantaneous temperature

spikes may be sampled by the part. The auto fan control logic calculates the PWM duty cycle for all

temperature readings. If Ramp Rate Control is disabled, the PWM output will jump or oscillate

between different PWM duty cycles causing the fan to suddenly change speeds, which creates

unwanted fan noise. If enabled, the PWM Ramp Rate Control logic will prevent the PWM output from

jumping, instead the PWM will ramp up/down towards the new duty cycle at a pre-determined ramp

rate.

Ramp Rate Control

The Ramp Rate Control logic limits the amount of change to the PWM duty cycle over a period of time.

This period of time is programmable via the Ramp Rate Control bits. For a detailed description of the

Ramp Rate Control bits see Table 8.31. For a description of the Ramp Rate Control logic see Ramp

Rate Control Logic on page 39.

Note:

■

RR1E, RR2E, and RR3E enable PWM Ramp Rate Control for PWM 1, 2, and 3 respectively.

■

RR1-2, RR1-1, and RR1-0 control ramp rate time for PWM 1

■

RR2-2, RR2-1, and RR2-0 control ramp rate time for PWM 2

■

RR3-2, RR3-1, and RR3-0 control ramp rate time for PWM 3

0111

1000

13.33

1001

1010

1011

26.67

1100

1101

1110

53.33

1111

Table 8.30 Register 62h, 63h: Min/Off, PWM Ramp Rate Control

Address

Read/

Write

Bit 7

(MSb)

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

(LSb)

Default

Value

62h

R/W

PWM 1 Ramp Rate Control

RES

RR1E

RR1-2

RR1-1

RR1-0

E0h

63h

R/W

PWM 2, PWM 3 Ramp

Rate Control

RR2E

RR2-2

RR2-1

RR2-0

RR3E

RR3-2

RR3-1

RR3-0

00h

Table 8.29 Register Setting vs. Temperature Range (continued)

RAN[3:0]

RANGE (

°C)

EMC6D103 데이터시트(PDF) 69 Page - SMSC Corporation

EMC6D103 데이터시트(HTML) 69 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

데이터시트 다운로드

링크 URL