전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

Preview PDF HTML

TLE9251VLE 데이터시트(PDF) 13 Page - Infineon Technologies AG

부품명 TLE9251VLE
상세설명  High Speed CAN Transceiver
PDF  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  INFINEON [Infineon Technologies AG]
홈페이지  http://www.infineon.com
Logo INFINEON - Infineon Technologies AG

TLE9251VLE 데이터시트(HTML) 13 Page - Infineon Technologies AG

Back Button TLE9251VLE Datasheet HTML 9Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 10Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 11Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 12Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 13Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 14Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 15Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 16Page - Infineon Technologies AG TLE9251VLE Datasheet HTML 17Page - Infineon Technologies AG Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 30 page
background image
Data Sheet
13
Rev. 1.0
2017-08-09
HS CAN Transceiver
High Speed CAN Transceiver
Changing the mode of operation
6.3
Mode changes by VCC undervoltage
When the transmitter supply VCC (VCC < VCC(U/F)) is in undervoltage condition, the TLE9251V might not be able to
provide the correct bus levels on the CANH and CANL output pins. To avoid any interference with the network
the TLE9251V blocks the transmitter and changes the mode of operation when an undervoltage event is
detected (see Figure 8 and Figure 9).
In Normal-operating mode an undervoltage event on transmitter supply VCC (VCC < VCC(U/F)) triggers a mode
change to Forced-receive-only mode.
In Forced-receive-only mode the undervoltage detection VCC (VCC < VCC(U/F)) is enabled. In Stand-by mode the
undervoltage detection is disabled. In these modes the TLE9251V can operate without the transmitter supply
VCC.
Figure 8
Mode changes by undervoltage events on VCC
Figure 9
Undervoltage on the transmitter supply VCC
STB
VCC
VIO
power-down
state
“X”
“X”
“off”
Normal-operating
mode
STB
VCC
VIO
0
“on”
“on”
Forced-
Receive-only
mode
STB
VCC
VIO
0
“off”
“on”
Stand-by
mode
STB
VCC
VIO
1
“X”
“on”
VIO “on”
VCC “off”
STB “0”
VIO “on”
VCC “on”
STB “0”
Forced-receive only mode
Normal-operating mode
Normal-operating mode
t
STB
digital supply voltage VIO = “on”
tDelay(UV)
VCC
hysteresis
VCC(UV,H)
t
VCC undervoltage monitor
VCC(UV,F)
VCC undervoltage monitor
VCC(UV,R)
tDelay(UV)
Assuming the STB remains “low”, for example the STB pin is
connected to GND.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com