P89V51RB2BBC datasheet(39/77 Pages) PHILIPS

39 / 77 page

Philips Semiconductors

P89V51RB2/RC2/RD2

8-bit microcontrollers with 80C51 core

Product data

Rev. 03 — 02 December 2004

39 of 77

9397 750 14341

7.5.5

Framing error

Framing error (FE) is reported in the SCON.7 bit if SMOD0 (PCON.6) = 1. If

SMOD0 = 0, SCON.7 is the SM0 bit for the UART, it is recommended that SM0 is set

up before SMOD0 is set to ‘1’.

7.5.6

More about UART mode 1

Reception is initiated by a detected 1-to-0 transition at RxD. For this purpose RxD is

sampled at a rate of 16 times whatever baud rate has been established. When a

transition is detected, the divide-by-16 counter is immediately reset to align its

rollovers with the boundaries of the incoming bit times.

The 16 states of the counter divide each bit time into 16ths. At the 7th, 8th, and 9th

counter states of each bit time, the bit detector samples the value of RxD. The value

accepted is the value that was seen in at least 2 of the 3 samples. This is done for

noise rejection. If the value accepted during the ﬁrst bit time is not 0, the receive

circuits are reset and the unit goes back to looking for another 1-to-0 transition. This

is to provide rejection of false start bits. If the start bit proves valid, it is shifted into the

input shift register, and reception of the rest of the frame will proceed.

The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the

following conditions are met at the time the ﬁnal shift pulse is generated: (a) RI = 0,

and (b) Either SM2 = 0, or the received stop bit = 1.

If either of these two conditions is not met, the received frame is irretrievably lost. If

both conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and

RI is activated.

TB8

The 9th data bit that will be transmitted in Modes 2 and 3. Set or

clear by software as desired.

RB8

In Modes 2 and 3, is the 9th data bit that was received. In Mode 1,

it SM2 = 0, RB8 is the stop bit that was received. In Mode 0, RB8

is undeﬁned.

Transmit interrupt ﬂag. Set by hardware at the end of the 8th bit

time in Mode 0, or at the stop bit in the other modes, in any serial

transmission. Must be cleared by software.

Receive interrupt ﬂag. Set by hardware at the end of the 8th bit

time in Mode 0, or approximately halfway through the stop bit time

in all other modes. (See SM2 for exceptions). Must be cleared by

software.

Table 27:

SCON - Serial port control register (address 98H) SM0/SM1 mode deﬁnition

SM0, SM1

UART mode

Baud rate

0 0

0: shift register

CPU clock/6

0 1

1: 8-bit UART

variable

1 0

2: 9-bit UART

CPU clock/32 or CPU clock/16

1 1

3: 9-bit UART

variable

Table 26:

SCON - Serial port control register (address 98H) bit description…continued

Bit

Symbol

Description

P89V51RB2BBC 데이터시트(PDF) 39 Page - NXP Semiconductors

P89V51RB2BBC 데이터시트(HTML) 39 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

데이터시트 다운로드

링크 URL