 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
FUSB302BVMPX 데이터시트(PDF) 16 Page - ON Semiconductor |
|
|
|||||||||||||||||||||||||||||
FUSB302BVMPX 데이터시트(HTML) 16 Page - ON Semiconductor |
|
|
16 / 32 page  FUSB302B www.onsemi.com 16 Table 11. CURRENT CONSUMPTION Symbol Parameter VDD (V) Conditions TA = −40 to +855C TA = −40 to +1055C (Note 11) TJ = −40 to +1255C Unit Min Typ Max Idisable Disabled Current 3.0 to 5.5 Nothing Attached, No I2C Transactions − 0.37 5 .0 mA Idisable Disabled Current (Note 11) 3.0 to 5.5 Nothing Attached, No I2C Transactions − 0.37 8.5 mA Itog Unattached (standby) Toggle Current 3.0 to 5.5 Nothing attached, TOGGLE = 1, PWR[3:0] = 1h, WAKE_EN = 0, TOG_SAVE_PWR2:1 = 01 − 25 40 mA Ipd_stby_meas BMC PD Standby Current 3.0 to 5.5 Device Attached, BMC PD Active But Not Sending or Receiving Anything, PWR[3:0] = 7h − 40 − mA Table 12. USB PD SPECIFIC PARAMETERS Symbol Parameter TA = −40 to +855C TA = −40 to +1055C (Note 11) TJ = −40 to +1255C Unit Min Typ Max tHardReset If a Soft Reset message fails, a Hard Reset is sent after tHardReset of CRCReceiveTimer expiring − − 5 ms tHardReset Complete If the FUSB302B cannot send a Hard Reset within tHardResetComplete time because of a busy line, then a I_HARDFAIL interrupt is triggered − − 5 ms tReceive This is the value for which the CRCReceiveTimer expires. The CRCReceiveTimer is started upon the last bit of the EOP of the transmitted packet 0.9 − 1.1 ms tRetry Once the CRCReceiveTimer expires, a retry packet has to be sent out within tRetry time. This time is hard to separate externally from tReceive since they both happen sequentially with no visible difference in the CC output − − 75 ms tSoftReset If a GoodCRC packet is not received within tReceive for NRETRIES then a Soft Reset packet is sent within tSoftReset time. − − 5 ms tTransmit From receiving a packet, we have to send a GoodCRC in response within tTransmit time. It is measured from the last bit of the EOP of the received packet to the first bit sent of the preamble of the GoodCRC packet − − 195 ms Table 13. IO SPECIFICATIONS Symbol Parameter VDD (V) Conditions TA = −40 to +855C TA = −40 to +1055C (Note 11) TJ = −40 to +1255C Unit Min Typ Max HOST INTERFACE PINS (INT_N) VOLINTN Output Low Voltage 3.0 to 5.5 IOL = 4 mA − − 0.4 V TINT_Mask Time from global interrupt mask bit cleared to when INT_N goes LOW 3.0 to 5.5 50 − − ms I2C INTERFACE PINS – STANDARD, FAST, OR FAST MODE PLUS SPEED MODE (SDA, SCL) (Note 6) VILI2C Low-Level Input Voltage 3.0 to 5.5 − − 0.51 V VIHI2C High-Level Input Voltage 3.0 to 5.5 1.32 − − V |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
