| 전자부품 데이터시트 검색엔진 |
|
M29DW128F 데이터시트(PDF) 24 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
M29DW128F 데이터시트(HTML) 24 Page - STMicroelectronics |
|
24 / 93 page ![]() 5 Software Protection M29DW128F 24/93 The Non-Volatile Modify Protection bits cannot be cleared individually, they can only be cleared all at the same time by issuing a Clear Non-Volatile Modify Protection Bits command. However if any one of the Non-Volatile Modify Protection bits has to be cleared, care should be taken to preprogram to ‘1’ all the Non-Volatile Modify Protection Bits prior to issuing the Clear Non-Volatile Modify Protection bits in order to prevent the over-erasure of previously cleared Non Volatile Modify Protection bits. It is crucial to prevent over-erasure because the process may lead to permanent damage to the Non-Volatile Modify Protection Bits and the device does not have any built-in means of preventing over-erasure. The device features a volatile Lock-Down bit which can be used to prevent changing the state of the Non-Volatile Modify Protection bits. When set to ‘1’, the Non-Volatile Modify Protection bits can no longer be modified; when set to ‘0’, the Non-Volatile Modify Protection bits can be set and reset using the Set Non-Volatile Modify Protection Bit command and the Clear Non- Volatile Modify Protection Bits command, respectively. The Lock-Down bit is set by issuing the Set Lock-Down Bit Command. It is not cleared using a command, but through a hardware reset or a power-down/power-up sequence. The parts are shipped with the Non-Volatile Modify Protection bits set to ‘0’. Locked blocks and Non-Volatile Locked blocks can co-exist in the same memory array. Refer to Table 10: Block Protection Status and Figure 7: Software Protection Scheme for details on the block protection mechanism. 5.2 Password Protection Mode The Password Protection mode provides a more advanced level of software protection than the Standard Protection mode. Prior to entering the Password Protection mode, it is necessary to set a password and to verify it (see Password Program command and Password Verify command). The Password Protection mode is then activated by programming the Password Protection Mode Lock bit to ‘1’. The Reset/Block Temporary Unprotect pin, RP, can be at VID or at VIH. This operation is not reversible and once the bit is programmed the device will permanently remain in the Password Protection mode. The Password Protection mode uses the same protection mechanisms as the Standard Protection mode (Block Lock/Unlock, Non-Volatile Protection). 5.2.1 Block Lock/Unlock Protection The Block Lock/Unlock Protection operates exactly in the same way as in the Standard Protection mode. 5.2.2 Non-Volatile Protection The Non-Volatile Protection is more advanced in the Password Protection mode. In this mode, the Lock-Down bit cannot be cleared through a hardware reset or a power-down/ power-up sequence. The Lock-Down bit is cleared by issuing the Password Protection Unlock command along with the correct password. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |