전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

A80603 데이터시트(PDF) 21 Page - Allegro MicroSystems

부품명 A80603
상세설명  LED Driver with Pre-Emptive Boost for Ultra-High Dimming Ratio and Low Output Ripple
PDF  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  ALLEGRO [Allegro MicroSystems]
홈페이지  http://www.allegromicro.com
Logo ALLEGRO - Allegro MicroSystems

A80603 데이터시트(HTML) 21 Page - Allegro MicroSystems

Back Button A80603 Datasheet HTML 17Page - Allegro MicroSystems A80603 Datasheet HTML 18Page - Allegro MicroSystems A80603 Datasheet HTML 19Page - Allegro MicroSystems A80603 Datasheet HTML 20Page - Allegro MicroSystems A80603 Datasheet HTML 21Page - Allegro MicroSystems A80603 Datasheet HTML 22Page - Allegro MicroSystems A80603 Datasheet HTML 23Page - Allegro MicroSystems A80603 Datasheet HTML 24Page - Allegro MicroSystems A80603 Datasheet HTML 25Page - Allegro MicroSystems Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 30 page
background image
LED Driver with Pre-Emptive Boost
for Ultra-High Dimming Ratio and Low Output Ripple
A80603 and
A80603-1
21
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
VDD
The VDD pin provides regulated bias supply for internal circuits.
Connect a CVDD capacitor with a value of 1 μF or greater to this
pin. The internal LDO can deliver up to 2 mA of current with a
typical VDD voltage of about 4.25 V. This allows it to serve as
the pull up voltage for FAULT pin.
Shutdown
If EN pin is pulled low for longer than tEN(OFF) (~16 ms), the
A80603 enters shutdown (sleep mode). The next time EN pin
goes high, all internal fault registers are cleared. The IC needs to
go through a complete soft start process after PWM goes high.
Figure 35: After EN = L for ~16 ms, the IC completely shuts down
so VDD (Blue) decays.
There is an alternative way to reset the internal fault status reg-
isters. By keeping EN = H and PWM = L for longer than 16 ms,
the A80603 clears all internal fault registers but does not go into
sleep mode. The next time PWM pin goes high, the IC will still
go through soft start process. The difference is that VDD voltage
and CLKOUT signal are always available as long as EN = H.
Figure 36: As long as EN = H, the IC does not shut down VDD and
CLKOUT. But internal latched faults are cleared by PWM = L for
~16 ms.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com