Output Configuration for Receiver

100 mA with short circuit protection

OFF-state leakage current:

NPN: < 200 µA sinking (see Application Note 2);

PNP: < 10 µA sourcing

ON-state saturation voltage

NPN: < 1.6 V at 100 mA

PNP: < 3.0 V at 100 mA

Output Configuration for all Other Models

Maximum Current ≤ 100 mA

PNP Output Voltage:

High ≥ Vsupply – Vsaturation

Low ≤ 1 V (≤ 1M Ω)

NPN Output Voltage:

High ≥ Vsupply – 1 V (≤ 1M Ω)

Low ≤ Vsaturation

Vsaturation ≤ 3 V

Output Response Time

Opposed mode: 1 millisecond ON/600 microseconds OFF

All other models: 850 microseconds ON/OFF

100 millisecond delay on power-up; outputs do not conduct during this time

Connections

2 m (6.5 ft) or 9 m (30 ft) 4-wire PVC cable, 150 mm (6 in) cable with 4-pin

threaded M8/Pico-style (Q) or M12/Euro-style (Q5) connector, or 4-pin

integral threaded M8/Pico-style connector (Q7), depending on the model

ordered

Indicators

Two LED Indicators: Power (green) and Output (amber)

Fixed-Field models:

Green on: Power ON

Amber on: Black (LO) wire conducting

All other models:

Green on: Power ON

Amber on: Black (LO) wire conducting

Amber flashing: Marginal excess gain (1 to 1.5×)

Black (LO) wire conducting

Adjustments

Diffuse, Retroreflective, and Polarized Retroreflective models (only):

Single-turn Sensitivity (Gain) adjustment potentiometer

Applications Notes

1.

Opposed mode sensor spacing can be reduced by alternating

emitters and receivers or by applying cross talk filters (visible red

models only)

2.

For receiver only: NPN off-state leakage current is <200 µA for load

resistances > 3kΩ or optically isolated loads. For load currents of

100 mA, leakage is <1% of load current.

Operating Conditions

–20 °C to +60 °C (–4 °F to +140 °F)

95% at +50 °C maximum relative humidity (non-condensing)

Environmental Rating

IEC IP67; NEMA 6

Vibration and Mechanical Shock

All models meet MIL-STD-202F, Method 201A (Vibration: 10 Hz to 60 Hz

maximum, 0.06 inch (1.52 mm) double amplitude, 10G maximum acceleration)

requirements. Also meets IEC 60947-5-2 (Shock: 30G 11 ms duration, half

sine wave) requirements.

Certifications

(Class 2 power supply

required)

Required Overcurrent Protection

WARNING: Electrical connections must be

made by qualified personnel in accordance

with local and national electrical codes and

regulations.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via Current

Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to

www.bannerengineering.com.

Supply Wiring (AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

Performance Curves

Opposed Mode Models

Excess Gain

Beam Pattern

1

10

100

0.1 m

0.3'

1.0 m

3.0'

10 m

30'

100 m

300'

1000

E

X

C

E

S

S

G

A

I

N

DISTANCE

Q20

Opposed

Infrared

Filter

Visible

15 m

49.2'

18 m

59.0'

21 m

68.9'

12 m

39.4'

9 m

29.5'

6 m

19.7'

3 m

9.8'

0

0

400 mm

800 mm

1200 mm

400 mm

800 mm

1200 mm

0

16"

31"

47"

16"

31"

47"

DISTANCE

Q20 Opposed Mode

Visible

Filters

Infrared

P/N 127816 Rev. M

www.bannerengineering.com - Tel: + 1 888 373 6767

3