전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

STR720 데이터시트(PDF) 104 Page - STMicroelectronics

부품명 STR720
상세설명  ARM720T 16/32-BIT MCU WITH 16K RAM, USB, CAN, 3 TIMERS, ADC, 6 COMMUNICATIONS INTERFACES
PDF  401 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  STMICROELECTRONICS [STMicroelectronics]
홈페이지  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

STR720 데이터시트(HTML) 104 Page - STMicroelectronics

Back Button STR720 Datasheet HTML 100Page - STMicroelectronics STR720 Datasheet HTML 101Page - STMicroelectronics STR720 Datasheet HTML 102Page - STMicroelectronics STR720 Datasheet HTML 103Page - STMicroelectronics STR720 Datasheet HTML 104Page - STMicroelectronics STR720 Datasheet HTML 105Page - STMicroelectronics STR720 Datasheet HTML 106Page - STMicroelectronics STR720 Datasheet HTML 107Page - STMicroelectronics STR720 Datasheet HTML 108Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 104 / 401 page
background image
STR720 - DRAM CONTROLLER (DRAMC)
104/401
10.4 Register description
The following paragraphs give detailed descriptions and operations of each of the bits in the
DRAMC registers.
Bank 1 Configuration Register (MB1Config)
Address Offset: 00h
Reset value: 0000h
The Bank 1 Configuration Register (MB1Config) is a 16-bit read/write control register used to
configure specific parameters of external region 1 (Bank 1).
The MB1Config control bits are described below.
Bit 15:12 reserved (should be written as zero and ignored on read ).
Bit 11:10 DEVWID[1:0]: Device Width.
This field defines the data width of the external memory device 0.
= 0b00. Byte (8 bit)
= 0b01. Half Word (16 bit)
= 0b10. Word (32 bit)
= 0b11. Reserved.
Bit 9:8
DATALAT[1:0]: Data Latency.
This field defines the number of memory clock cycles between the start of a
memory read access and the first valid data. This parameter is usually indicated in
SDRAM datasheets as CAS latency. The DATALAT value is valid between 0 and 3.
Bit 7:5
SETUPTIME[2:0]: Setup Time.
This field defines the number of memory clock cycles the memory drivers spends
in a wait state before accessing the external memory. This parameter is usually
indicated in SDRAM datasheets as RAS-CAS delay. The SETUPTIME value is
valid between 0 and 7.
Note
SETUPTIME field should be set using the RAS-CAS delay value found on SDRAM
datasheet minus 1. As an example to get a RAS-CAS delay of 2 clock cycles,
SETUPTIME should be configured to 1.
Bit 4:2
IDLETIME[2:0]: Idle Time.
This field defines the minimum time the memory driver must spend in the IDLE
state following memory accesses (the value defines the number of memory clock
cycles). This parameter is usually indicated in SDRAM datasheets as precharge
delay. The IDLETIME value is valid between 0 and 7.
15
14
13
12
11
10
9
8
7
6543210
reserved
DEVWID[1:0]
DATALAT[1:0]
SETUPTIME[2:0]
IDLETIME[2:0]
SDRAMCOL[1:0]
rw
rw
rw
rw
rw
1



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com