AMC3301 datasheet(7/23 Pages) TI1

7 / 23 page

AMC3301

www.ti.com

SBAS917 – AUGUST 2019

Product Folder Links: AMC3301

Submit Documentation Feedback

6.7 Safety-Related Certifications

VDE

Certified according to DIN VDE V 0884-11 (VDE V 0884-11): 2017-01,

DIN EN 60950-1 (VDE 0805 Teil 1): 2014-08, and

DIN EN 60065 (VDE 0860): 2005-11

Recognized under 1577 component recognition and

CSA component acceptance NO 5 programs

Reinforced insulation

Single protection

Certificate planned

(1)

The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The IS

and PS parameters represent the safety current and safety power, respectively. Do not exceed the maximum limits of IS and PS. These

limits vary with the ambient temperature, TA.

The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for

leaded surface-mount packages. Use these equations to calculate the value for each parameter:

TJ = TA + RθJA × P, where P is the power dissipated in the device.

TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum junction temperature.

PS = IS × VDDmax, where VDDmax is the maximum low-side voltage.

6.8 Safety Limiting Values

Safety limiting

(1) intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A failure

ofthe I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to

overheatthe die and damage the isolation barrier potentially leading to secondary system failures.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Safety input, output, or supply current

RθJA = 73.5°C/W, VDD = 5.5 V, TJ =

150°C, TA = 25°C, see Figure 2

309

Safety input, output, or supply current

RθJA = 73.5°C/W, VDD = 3.6 V, TJ =

150°C, TA = 25°C, see Figure 2

472

Safety input, output, or total power

RθJA = 73.5°C/W, TJ = 150°C, TA = 25°C,

see Figure 3

1700

Maximum safety temperature

150

°C

(1)

The typical value includes one sigma statistical variation.

(2)

The typical value is at VDD1 = 3.3 V.

(3)

Also see the Analog Input section for more details.

6.9 Electrical Characteristics

minimum and maximum specifications apply from TA = –40°C to +125°C, VDD = 3.0 V to 5.5 V, INP = –250 mV to +250 mV,

and INN = HGND = 0V; typical specifications are at TA = 25°C, and VDD = 3.3 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

ANALOG INPUT

VCMov

Common-mode overvoltage detection

level

(VINP + VINN) / 2 to HGND

Hysteresis of common-mode overvoltage

detection level

VOS

Input offset voltage (1)

Initial, at TA = 25°C, INP = INN =

HGND (2)

–0.2

±0.03

0.2

TCVOS

Input offset drift (1)

–5

±1.5

uV/°C

CMRR

Common-mode rejection ratio

fIN = 0 Hz, VCM min ≤ VCM ≤ VCM max

–100

fIN = 10 kHz, VCM min ≤ VCM ≤ VCM max

–98

PSRR

Power-supply rejection ratio

At dc

–103

100-mV and 10-kHz ripple

–86

CIN

Single-ended input capacitance (3)

INN = HGND, fIN = 310 kHz

CIND

Differential input capacitance (3)

fIN = 310 kHz

RIN

Single-ended input resistance (3)

INN = HGND

kΩ

RIND

Differential input resistance (3)

IIB

Input bias current

INP = INN = HGND; IIB = (IIBP + IIBN) / 2

–41

–30

–24

TCIIB

Input bias current drift

±1

nA/°C

IIO

Input offset current

IIO = IIBP – IIBN

±5

AMC3301 데이터시트(PDF) 7 Page - Texas Instruments

AMC3301 데이터시트(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

데이터시트 다운로드

링크 URL