AT90LS8535 datasheet(37/127 Pages) ATMEL

37 / 127 page

AT90S/LS8535

1041H–11/01

Note:

X = A or B.

In PWM mode, these bits have a different function. Refer to Table 15 for a detailed

description. When changing the COM1X1/COM1X0 bits, Output Compare Interrupt 1

must be disabled by clearing their Interrupt Enable bits in the TIMSK Register. Other-

wise an interrupt can occur when the bits are changed.

• Bits 3..2 – Res: Reserved Bits

These bits are reserved bits in the AT90S8535 and always read zero.

• Bits 1..0 – PWM11, PWM10: Pulse Width Modulator Select Bits

These bits select PWM operation of Timer/Counter1 as specified in Table 12. This mode

is described on page 40.

Timer/Counter1 Control

• Bit 7 – ICNC1: Input Capture1 Noise Canceler (4 CKs)

When the ICNC1 bit is cleared (zero), the Input Capture Trigger Noise Canceler function

is disabled. The input capture is triggered at the first rising/falling edge sampled on the

ICP (input capture pin) as specified. When the ICNC1 bit is set (one), four successive

samples are measured on the ICP (input capture pin), and all samples must be high/low

according to the input capture trigger specification in the ICES1 bit. The actual sampling

frequency is XTAL clock frequency.

• Bit 6 – ICES1: Input Capture1 Edge Select

While the ICES1 bit is cleared (zero), the Timer/Counter1 contents are transferred to the

Input Capture Register (ICR1) on the falling edge of the input capture pin (ICP). While

the ICES1 bit is set (one), the Timer/Counter1 contents are transferred to the Input Cap-

ture Register (ICR1) on the rising edge of the input capture pin (ICP).

• Bits 5, 4 – Res: Reserved Bits

These bits are reserved bits in the AT90S8535 and always read zero.

Table 11. Compare 1 Mode Select

COM1X1

COM1X0

Description

Timer/Counter1 disconnected from output pin OC1X

Toggle the OC1X output line.

Clear the OC1X output line (to zero).

Set the OC1X output line (to one).

Table 12. PWM Mode Select

PWM11

PWM10

Description

PWM operation of Timer/Counter1 is disabled

Timer/Counter1 is an 8-bit PWM

Timer/Counter1 is a 9-bit PWM

Timer/Counter1 is a 10-bit PWM

Bit

3210

$2E ($4E)

ICNC1

ICES1

––

CTC1

CS12

CS11

CS10

TCCR1B

Read/Write

R/W

Initial Value

0000

AT90LS8535 데이터시트(PDF) 37 Page - ATMEL Corporation

AT90LS8535 데이터시트(HTML) 37 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL