| 전자부품 데이터시트 검색엔진 |
|
LTC2802 데이터시트(PDF) 6 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
LTC2802 데이터시트(HTML) 6 Page - Analog Devices |
|
6 / 32 page ![]() LTC2873 6 REV B For more information www.analog.com The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VL = 3.3V, TE485 = VL, LB = 0V unless otherwise noted. (Notes 2, 6) SWITCHING CHARACTERISTICS SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS tZLSR232, tZHSR232 Receiver Enable from Shutdown Time (Note 7) VDD = 7.0V, VEE = –6.3V, 485/232 = 0V, RL = 1kΩ, CL = 150pF, SHDN ↑ (Figure 12) l 5 12 µs tLZSR232, tHZSR232 Receiver Disable Into Shutdown Time 485/232 = 0V, RL = 1kΩ, CL = 150pF SHDN ↓ (Figure 12) l 0.4 2 μs Mode Change Characteristics tRDY VDD and VEE Supply Rise Time (Time from Shutdown to RS485 Ready) (Figure 13) l 0.2 1 ms tDR232 Time from RS485 Mode to RS232 Mode RS232 Driver Ready (Figure 14) l 0.2 1 µs tR232 Time from RS485 Mode to RS232 Mode RS232 Receiver Ready (Figure 14) l 0.8 3 µs tDR485 Time from RS232 Mode to RS485 Mode RS485 Driver and Receiver Ready (Figure 14) l 70 250 ns Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. Note 3: Guaranteed by other measured parameters and not tested directly. Note 4: Time from SHDN ↑ until VDD ≥ 5V and VEE ≤ –5V. External components as shown in the Typical Application section. Note 5: Guaranteed by design and not subject to production test. Note 6:Testing was done with VDD and VEE back driven to valid supply levels for functions that require these supplies, unless otherwise noted. Note 7: If enabling from shutdown, where VDD and VEE supplies are collapsed, allow the extra time it takes to generate valid VDD and VEE supplies (tRDY). |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |