| 전자부품 데이터시트 검색엔진 |
|
TPS2340APFPR 데이터시트(PDF) 9 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TPS2340APFPR 데이터시트(HTML) 9 Page - Texas Instruments |
|
9 / 27 page ![]() TPS2340A SLUS528A – MARCH 2002 – REVISED AUGUST 2002 9 www.ti.com Terminal Functions TERMINAL I/O DESCRIPTION NAME NO. I/O DESCRIPTION RESETA 35 O PCI RESET signal to slot A. Conforms to PCI 2.2 local bus specification for 3.3-V signaling. This pin is typically tied to the PCI connector. RESETB 26 O PCI RESET signal to slot B. Conforms to PCI 2.2 local bus specification for 3.3-V signaling. This pin is typically tied to the PCI connector. SIC 44 I Serial input clock. Shift serial data into device one bit position on rising edge. SIDI 20 I Serial input data Input. The serial shift register input from a down-stream TPS2340. SIDO 41 I/O Serial input data output. The serial shift register output to the PCI hot-plug controller or the up-stream TPS2340. When PGOOD is low, SIDO is undriven and pulled up to DIGVCC with a 100-k Ω resistor. During the rising edge of PGOOD, the TPS2340A latches SIDO as MODE0. SIL 16 I Serial input load. Pulse low to synchronously parallel load external serial input shift registers on the next rising edge of SIC. SOC 17 I Serial output clock. Shift serial output data into parallel output registers one bit position on rising edge. SODI 42 I Serial output data input. Serial output data shifted into parallel output registers. SODO 19 I/O Serial output data output. Serial output data shifted to the down-stream TPS2340. When PGOOD is low, SODO is undriven and pulled up to DIGVCC with a 100-k Ω resistor. During the rising edge of PGOOD, the TPS2340A latches SODO as MODE1. SOLC 39 I Serial output latch clock. Latch parallel register data on rising edge. SORLC 22 I Serial output reset latch clock. Latch parallel register data on rising edge (PCI RESET latches only). SOR 40 I Serial output reset. Clears parallel register data. SORR 21 I Serial output reset reset. Clears parallel register data (PCI RESET latches only). SWA 46 I Slot A switch input. Low indicates the slot is populated. This input has hysteresis and a 100-k Ω pull-up to 3VAUXI, requiring only a capacitor to ground for debouncing mechanical noise. For testing pur- poses, pulling SWA to 5 V enables the slot main power and disables the slot auxilliary power, bypass- ing the serial interface. SWB 14 I Slot B switch input. Low indicates the slot is populated. This input has hysteresis and a 100-k Ω pull-up to 3VAUXI, requiring only a capacitor to ground for debouncing mechanical noise. For testing pur- poses, pulling SWB to 5 V enables the slot main power and disables the slot auxilliary power, bypass- ing the serial interface. TEST 23 I When asserted on the rising edge of PGOOD, device enters test modes based on the states of the MODE pins. See In–Circuit Test section of the datasheet. When asserted after PGOOD is asserted, maps the Pwrenx and ANDed Faultx internal signals to PWRLED and ATTLED pins for test purposes. TEST has a 100-k Ω pull-down resistor to ground. V5IN 49 I 5-V input to the device. A 0.1- µF bypass capacitor from V5IN to PWRGND is recommended. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |