2

Specifications are subject to change without notice (18.06.07)

DMC01, PMC01

Supply Specifications

General Specifications

Power supply

Overvoltage cat. III

Rated operational voltage

(IEC 60664, IEC 60038)

through terminals:

A1, A2 or A1, A3 (DMC01)

B48

24 or 48 VAC ± 15%

45 to 65 Hz

B23

115 or 230 VAC ± 15%

45 to 65 Hz

724

24 VDC ± 20%

2, 10 (PMC01)

024

24 VAC ± 15%,45 to 65 Hz

115

115 VAC ± 15%,45 to 65 Hz

230

230 VAC ± 15%,45 to 65 Hz

724

24 VDC ± 20%

Voltage interruption

≤ 10 ms

Rated operational power

AC supply:

5 VA

DC supply:

2 W

Power ON delay

≤ 100 ms

Reaction time from trigger

Delayed contact(s)

< 10 ms

Instantaneous contcat

< 20 ms

Indication for

Power supply ON

LED, green

Output relays ON

LED, yellow (flashing when

timing)

Environment

(EN 60529)

Degree of protection

IP 20

Pollution degree

3 (DMC01), 2 (PMC01)

(IEC 60664)

Operating temperature

-20 to 60 °C, R.H. < 95%

Storage temperature

-30 to 80 °C, R.H. < 95%

Housing

Dimensions

DMC01C

22.5 x 80 x 99.5 mm

DMC01D

45 x 80 x 99.5 mm

PMC01

36 x 80 x 94 mm

Weight

120 to 260g depending on

model

Screw terminals

(DMC01)

Tightening torque

Max 0.5 Nm according to

IEC EN 60947

Approval

UL, CSA

CE Marking

Yes

EMC

Electromagnetic Compatibility

Immunity

According to EN 61000-6-2

Emission

According to EN 61000-6-3

Timer Specifications

According to EN 61812-1

Function/Range/Time Setting

Adjust the function setting

the DIP switches 1 to 6 as

shown below (1 to 4 for

DMC01Cxxx).

Note 1: DIP switch 5 must

be

kept

ON when

using

PMC01Dxxx.

Note 2: DIP switch 6 does

not have any effect on the

PMC01Cxxx working mode.

To access the DIP switches

open the grey plastic cover

using

a

screwdriver

as

shown below.

Upper knob:

Selection of function:

Op - Delay

on

operate,

manual start

Oa - Delay

on

operate,

automatic and manual

start

In - Interval, manual start

Ia - Interval,

automatic

and manual start

Nr - Interval with no time

reset, manual start

Na - Interval with no time

reset, automatic and

manual start

Dr - Delay on release

Centre knob:

Time

setting

on

relative

scale: 1 to 10 with respect

to the chosen range.

Lower knob:

Setting of time range

External

potentiometer

(DMC01D, PMC01C):

Time

setting

on

relative

scale: 1 to 10 with respect

to the chosen range.

Output Specifications

Output

1 or 2 x SPDT relay

Rated insulation voltage

250 VAC (RMS)

Resistive loads

AC 1

8 A @ 250 VAC

DC 12

5 A @ 24 VDC

Small inductive loads AC 15

2.5 A @ 250 VAC

DC 13

2.5 A @ 24 VDC

Mechanical life

Electrical life

(at 8 A, 250 V, cos

ϕ = 1)

Operating frequency

< 7200 operations / h

Dielectric strength

Dielectric voltage

2 kVAC (RMS)

Rated impulse withstand volt. 4 kV (1.2/50 µs)

Sensor type selection

ON ON OFF OFF: PNP/NPN sensor,

Open collector

or contact

OFF OFF ON ON:

Namur sensor

Time setting (DMC01D and PMC01C)

ON:

Centre knob on front

OFF:

External trimmer

Second relay

ON:

Instantaneous

OFF:

DPDT

DMC01D,

PMC01C,

PMC01D

DMC01C