LM2745 datasheet(11/23 Pages) NSC

11 / 23 page

Application Information (Continued)

For example, if the master supply output voltage slew rate

was 1V/ms and the desired delay time between the startup

of the master supply and LM2745/8 output voltage was 5 ms,

then the desired SD pin slew rate would be (1.08V/5 ms) =

0.216V/ms. Due to the internal impedance of the SD pin, the

maximum recommended value for R

S2 is1k

Ω. To achieve

the desired slew rate, R

S1 would then be 274

Ω. A timing

diagram for this example is shown in Figure 7.

SD PIN IMPEDANCE

When connecting a resistor divider to the SD pin of the

LM2745/8 some care has to be taken. Once the SD voltage

goes above V

SD-IH, a 17 µA pull-up current is activated as

shown in Figure 8. This current is used to create the internal

hysteresis ()170 mV); however, high external impedances

will affect the SD pin logic thresholds as well. The external

impedance used for the sequencing divider network should

preferably be a small fraction of the impedance of the SD pin

for good performance (around 1 k

Ω).

MOSFET GATE DRIVERS

The LM2745/8 has two gate drivers designed for driving

N-channel MOSFETs in a synchronous mode. Note that

unlike most other synchronous controllers, the bootstrap

capacitor of the LM2745/8 provides power not only to the

driver of the upper MOSFET, but the lower MOSFET driver

too (both drivers are ground referenced, i.e. no floating

driver).

Two things must be kept in mind here. First, the BOOT pin

has an absolute maximum rating of 18V. This must never be

exceeded, even momentarily. Since the bootstrap capacitor

is connected to the SW node, the peak voltage impressed on

the BOOT pin is the sum of the input voltage (V

IN) plus the

voltage across the bootstrap capacitor (ignoring any forward

drop across the bootstrap diode). The bootstrap capacitor is

charged up by a given rail (called V

BOOT_DC here) whenever

the upper MOSFET turns off. This rail can be the same as

CC or it can be any external ground-referenced DC rail. But

care has to be exercised when choosing this bootstrap DC

rail that the BOOT pin is not damaged. For example, if the

desired maximum V

IN is 14V, and VBOOT_DC is chosen to be

the same as V

CC, then clearly if the VCC rail is 6V, the peak

voltage on the BOOT pin is 14V + 6V = 20V. This is unac-

ceptable, as it is in excess of the rating of the BOOT pin. A

CC of 3V would be acceptable in this case. Or the VIN range

must be reduced accordingly. There is also the option of

deriving the bootstrap DC rail from another 3V external rail,

independent of V

CC.

The second thing to be kept in mind here is that the output of

the low-side driver swings between the bootstrap DC rail

level of V

BOOT_DC and Ground, whereas the output of the

high-side driver swings between V

IN+VBOOT_DC

and

Ground. To keep the high-side MOSFET fully on when de-

sired, the Gate pin voltage of the MOSFET must be higher

than its instantaneous Source pin voltage by an amount

equal to the ’Miller plateau’. It can be shown that this plateau

is equal to the threshold voltage of the chosen MOSFET plus

a small amount equal to Io/g. Here Io is the maximum load

current of the application, and g is the transconductance of

this MOSFET (typically about 100 for logic-level devices).

That means we must choose V

BOOT_DC to at least exceed

20137411

FIGURE 7. Delay for Sequencing

20137406

FIGURE 8. SD Pin Logic

LM2745 데이터시트(PDF) 11 Page - National Semiconductor (TI)

LM2745 데이터시트(HTML) 11 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

데이터시트 다운로드

링크 URL