MODEL: TC10EM

TC10EM SPECIFICATIONS

ES-9581 Rev.4 Page 1/7

http://www.m-system.co.jp/

Temperature Controller TC10 Series

TEMPERATURE CONTROLLER

(Modbus, 5 digit, LED display type, size 96 x 96 mm)

Functions & Features

• Two PID controllers*

• Universal input x 2 points, control output x 4 points,

discrete input x 2 points, clamp-on current sensor input x 2

points

• 2 universal inputs configurable to T/C, RTD, DC current or

voltage independently

• Discrete inputs usable to switch PID bank or operation

mode

• Control outputs configurable to MV, PV or alarm

• Clamp-on current sensor input enables to detect heater

wire break or over current

• Auto tuning function

*Only single loop control is available while loop 1 remote SP

is enabled.

96(3.8)

108(4.25)

mm (inch)

96(3.8)

MODEL: TC10EM–[1]–M2

ORDERING INFORMATION

• Code number: TC10EM-[1]-M2

Specify a code from below for [1].

(e.g. TC10EM-A-M2)

[1] CONTROL OUTPUT

A: 0 – 20 mA DC (Load resistance 500 Ω max.)

Open-collector 2 points

V: 0 – 10 V DC (Load resistance 2 kΩ max.)

Open-collector 2 points

P: 12 V pulse (Load resistance 600 Ω max.)

Open-collector 2 points

POWER INPUT

AC Power

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

RELATED PRODUCTS

• PC configurator software (model: TC10CFG)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

• Clamp-on current sensor (model: CLSE)

(Used for detecting the heater wire break)

GENERAL SPECIFICATIONS

Construction: Panel flush mounting

Degree of protection: IP65; applicable to the front panel of

the unit with single mounting according to the specified

panel cutout

Configuration jack: 2.5 dia. miniature jack connector;

RS-232-C level

Connection: M3 separable screw terminal (torque 0.5 N·m)

Solderless terminal: Refer to the drawing at the end of the

section.

Recommended manufacturer: Japan Solderless Terminal

MFG.Co.Ltd, Nichifu Co.,ltd

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (black)

Isolation: Pv1 to Pv2 to CT1 or CT2 to Di1 or Di2 to MV1 or

MV2 to Do1 or Do2 to Modbus to power

CT Input waveform

RMS sensing: Up to 15 % of 3rd harmonic content

Control mode: Standard PID, heating and cooling control

(ON/OFF, PID)

Proportional band (P): 0.1 to 3200.0 (temperature unit)

Integral time (I): 0 to 3999 sec.

Derivative time (D): 0.0 to 999.9 sec.

Auto-tuning: Limit cycle method

Alarm: Deviation high & low, absolute high & low, etc.

Sampling cycle: 100 msec.

Control cycle: 1.0 to 99.9 sec.

(100 msec. fixed for Mv output 0 - 20 mA DC

and 0 - 10 V DC)

Mv output range: -5 - +105 % for output scale

Parameters: Stored in non-volatile memory; write/erase

cycle endurance: less than 1 000 000

Parameter setting: With front panel operation buttons or PC

configurator software (model: TC10CFG)

• Universal input

• Burnout

• Control output

• Loop