| 전자부품 데이터시트 검색엔진 |
|
MAX4313 데이터시트(PDF) 2 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX4313 데이터시트(HTML) 2 Page - Maxim Integrated Products |
|
2 / 4 page ![]() MAX4313 Evaluation Kit 2 _______________________________________________________________________________________ Detailed Description Setting the Voltage Gain (MAX4310) The gain of the MAX4310’s amplifier can be set by changing the feedback (RF) and gain-set (RG) resis- tors. Refer to the MAX4310/MAX4313 data sheet for recommended values. Control of Digital Inputs (A0, SHDN) Jumpers JU1 and JU2 provide the user with manual control of the multiplexer input address (A0) and shut- down (SHDN), respectively (Table 1). An external con- troller may also be used on either input by connecting the controller to the appropriate pad and removing the shunt from JU1 or JU2. The MAX4313’s A0 and SHDN pins should not be left floating. For a single +5V sup- ply, A0 and SHDN are CMOS-logic compatible. The logic-high threshold is VCC - 1.2V, and the logic-low threshold is VCC - 2.8V. Layout Considerations The PC board layout has been optimized for high-speed signals and low distortion, with careful attention given to grounding, power-supply bypassing, and signal- path layout. The small, surface-mount, ceramic bypass capacitors (C1, C3) have been placed as close as pos- sible to the amplifier’s supply pins. The ground plane has been removed around and under the amplifier to reduce stray capacitance. Capacitance at the feedback pin has been minimized by using 0805-size feedback and gain-set resistors and by removing the adjacent ground plane. Table 1. Jumper Selection VCC C2 10 µF 10V C3 0.1 µF C4 10 µF 10V C1 0.1 µF R1 49.9 Ω R2 49.9 Ω RG* 0 Ω 36 4 VCC VEE VEE VCC IN0 5 IN1 IN0 IN1 A0 A0 R3 1 GND 7 VCC JU1 500 Ω 500 Ω RF* OPEN IN1 1 2 3 IN0 8 2 3 2 1 JU2 OUT SHDN OUT 49.9 Ω SHDN ENABLE DISABLE MAX4313 U1 MUX * REQUIRED FOR MAX4310 Figure 1. MAX4313 EV Kit Schematic JUMPER JUMPER POSITION FUNCTION JU1 1–2 Select IN1. Open Drive pad A0 with external signal. 1–2 Disable output. 2–3 Enable output. Open Drive pad SHDN with external signal. 2–3 Select IN0. JU2 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |