| 전자부품 데이터시트 검색엔진 |
|
MIC2582 데이터시트(PDF) 12 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MIC2582 데이터시트(HTML) 12 Page - Microchip Technology |
|
12 / 32 page ![]() MIC2582/3 DS20006573A-page 12 2021 Microchip Technology Inc. Note: Please refer to the Start-Up Cycle section and Figure 1-3 for a detailed explanation of the start-up and oper- ation sequence of the MIC2582 pins shown in Table 3-1. 7 15 SENSE Circuit Breaker Sense input: A resistor between this pin and VCC sets the current-limit threshold. Whenever the voltage across the sense resistor exceeds the slow trip current-limit threshold (VTRIPS- LOW), the GATE voltage is adjusted to ensure a constant load cur- rent. If VTRIPSLOW (50 mV) is exceeded for longer than time period tOCSLOW, then the circuit breaker is tripped and the GATE pin is immediately pulled low. If the voltage across the sense resistor exceeds the fast trip circuit breaker threshold, VTRIPFAST, at any point due to fast, high amplitude power supply faults, then the GATE pin is immediately brought low without delay. To disable the circuit breaker, the SENSE and VCC pins can be tied together. The default VTRIPFAST for either device is 100 mV. Other fast trip thresh- olds are available: 150 mV, 200 mV, or OFF (VTRIPFAST disabled). Please contact Microchip for availability of other options. 8 16 VCC Positive Supply input: 2.3V to 13.2V. The GATE pin is held low by an internal undervoltage lockout circuit until VCC exceeds a thresh- old of 2.2V. If VCC exceeds 13.2V, an internal shunt regulator pro- tects the chip from transient voltages up to 20V at the VCC and SENSE pins. — 2 PWRGD Power Good output: Open-drain N-channel device, active-high. When the voltage at the FB pin is lower than 1.24V, PWRGD output is held low. When the voltage at the FB pin exceeds 1.24V, then PWRGD is asserted immediately. The PWRGD pin requires a pull-up resistor (10 kΩ minimum) to VCC. — 5 CFILTER Current-Limit Response timer: A capacitor connected to this pin defines the period of time (tOCSLOW) in which an overcurrent event must last to signal a fault condition and trip the circuit breaker. If no capacitor is connected, then tOCSLOW defaults to 5 µs. — 11 /FAULT Circuit Breaker Fault Status output: Open-drain N-channel device, active-low. The /FAULT pin is asserted when the circuit breaker trips due to an overcurrent condition or when an undervoltage lock- out condition exists. The/FAULT pin requires a pull-up resistor (10 kΩ minimum) to VCC. — 13 DIS Discharge output: When the MIC2583/3R is turned off, a 500Ω internal resistor at this output allows the discharging of any load capacitance to ground. — 6, 9, 10 NC No internal connection. TABLE 3-1: PIN FUNCTION TABLE (CONTINUED) Pin Number SOIC-8 Pin Number QSOP-16 Pin Name Description |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |