전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

MDEV-GPS-RM 데이터시트(PDF) 17 Page - Linx Technologies

부품명 MDEV-GPS-RM
상세설명  RM Series GPS Receiver Module
PDF  27 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  LINX [Linx Technologies]
홈페이지  https://linxtechnologies.com/wp/
Logo LINX - Linx Technologies

MDEV-GPS-RM 데이터시트(HTML) 17 Page - Linx Technologies

Back Button MDEV-GPS-RM Datasheet HTML 13Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 14Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 15Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 16Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 17Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 18Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 19Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 20Page - Linx Technologies MDEV-GPS-RM Datasheet HTML 21Page - Linx Technologies Next Button
Zoom Inzoom in Zoom Outzoom out
 17 / 27 page
background image
–
–
–
–
28
29
Set Datum
This configures the current datum that is used.
Datum = the datum number to be used.
Reference datums are data sets that describe the shape of the Earth
based on a reference point. There are many regional datums based on a
convenient local reference point. Different datums use different reference
points, so a map used with the receiver output must be based on the same
datum. WGS84 is the default world referencing datum.
The module supports 223 different datums. These are listed in Appendix A.
The following example sets the datum to WGS84.
$PMTK330,0*2E<CR><LF>
The following example reads the current datum and the module replies with
datum 0, which is WGS84.
$PMTK430*35<CR><LF>
$PMTK530,0*28<CR><LF>
Set Datum Command and Response
Write Message
Start
Msg ID
Datum
Checksum
End
$PMTK
330
,Datum
*Cksum
<CR><LF>
Acknowledge Response Message
Start
Msg ID
CMD
Flag
Checksum
End
$PMTK
001
,330
,Flg
*Cksum
<CR><LF>
Read Message
Start
Msg ID
Checksum
End
$PMTK
430
*35
<CR><LF>
Response Message
Start
Msg ID
Datum
Checksum
End
$PMTK
530
,Datum
*Cksum
<CR><LF>
Figure 31: Set Datum Command and Response
Static Navigation Threshold
This configures the speed threshold to trigger static navigation. If the
measured speed is below the threshold then the module holds the current
position and sets the speed to zero.
Static navigation is disabled by default, and is set for walking speed.
Thold = speed threshold, from 0 to 2.0m/s. 0 = disabled.
The following example sets the threshold to 1.2m/s.
$PMTK386,1.2*3E<CR><LF>
The following example reads the static navigation threshold and the module
responds with 1.2m/s
$PMTK447*35<CR><LF>
$PMTK527,1.20*03<CR><LF>
The static navigation threshold configuration returns to the default values
after a reset or restart.
Static Navigation Threshold Command and Response
Write Message
Start
Msg ID
Thold
Checksum
End
$PMTK
386
,Thold
*Cksum
<CR><LF>
Acknowledge Response Message
Start
Msg ID
CMD
Flag
Checksum
End
$PMTK
001
,386
,Flg
*Cksum
<CR><LF>
Read Message
Start
Msg ID
Checksum
End
$PMTK
447
*35
<CR><LF>
Response Message
Start
Msg ID
Thold
Checksum
End
$PMTK
527
,Thold
*Cksum
<CR><LF>
Figure 32: Static Navigation Threshold Command and Response



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com