R7FA4M2AB3CFL datasheet(25/92 Pages) RENESAS

25 / 92 page

Table 2.7

Operating and standby current (2 of 2)

Parameter

Symbol

Min Typ

Max

Unit Test conditions

Analog

power

supply

current

During 12-bit A/D conversion

AICC

—

0.8

1.1

—

Temperature sensor

—

0.1

0.2

—

During D/A conversion (per unit)

Without AMP output

—

0.1

0.2

—

With AMP output

—

0.6

1.1

—

Waiting for A/D, D/A conversion (all units)

—

0.5

1.0

—

ADC12, DAC12 in standby modes (all units)*9

—

0.4

4.0

µA

—

Reference

power

supply

current

(VREFH0)

During 12-bit A/D conversion (unit 0)

AIREFH0

—

120

µA

—

Waiting for 12-bit A/D conversion (unit 0)

—

0.07

0.5

µA

—

ADC12 in standby modes (unit 0)

—

0.07

0.5

µA

—

Reference

power

supply

current

(VREFH)

During D/A conversion (per unit)

Without AMP output AIREFH

—

0.1

0.4

—

With AMP ouput

—

0.1

0.4

—

Waiting for D/A (all units) conversion

—

0.07

0.8

µA

—

USB

operating

current

Low speed

USB

ICCUSBLS

—

3.5

6.5

VCC_USB

Full speed

USB

ICCUSBFS

—

4.0

10.0

VCC_USB

LDOn operating current (1 unit)*15

ICCLDO

—

0.18

—

PLL2-LDO operating current

ICCPLL2LDO —

0.21

—

Note 1. Supply current values are with all output pins unloaded and all input pull-up MOSs in the off state.

Note 2. Measured with clocks supplied to the peripheral functions. This does not include the BGO operation.

Note 3. ICC depends on f (ICLK) as follows.

ICC Max. = 0.53 × f + 12 (max. operation in high-speed mode)

ICC Typ. = 0.05 × f + 1.85 (normal operation in high-speed mode, all peripheral clocks disabled)

ICC Typ. = 0.12 × f + 0.69 (low-speed mode)

ICC Max. = 0.13 × f + 12 (sleep mode)

Note 4. This does not include the BGO operation.

Note 5. Supply of the clock signal to peripherals is stopped in this state. This does not include the BGO operation.

Note 6. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (1.563 MHz).

Note 7. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (3.125 MHz).

Note 8. Reference value

Note 9. When the MCU is in Software Standby mode or the MSTPCRD.MSTPD16 (12-Bit A/D Converter 0 Module Stop bit) is in the

module-stop state.

Note 10. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (15.6 kHz).

Note 11. PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (512 Hz). FCLK is the same frequency as that of ICLK.

Note 12. PLL output frequency = 100MHz.

Note 13. PLL output frequency = 200MHz.

Note 14. PLL2-LDO disabled.

Note 15. n = 0, 1

RA4M2 Datasheet

2. Electrical Characteristics

R01DS0367EJ0110 Rev.1.10

Jan 27, 2021

Page 25 of 92

R7FA4M2AB3CFL 데이터시트(PDF) 25 Page - Renesas Technology Corp

R7FA4M2AB3CFL 데이터시트(HTML) 25 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

데이터시트 다운로드

링크 URL