DI35 datasheet(71/416 Pages) MICROCHIP

71 / 416 page

 2016-2018 Microchip Technology Inc.

DS30010118D-page 71

PIC24FJ256GA705 FAMILY

6.0

FLASH PROGRAM MEMORY

The PIC24FJ256GA705 family of devices contains

internal Flash program memory for storing and execut-

ing application code. The program memory is readable,

writable and erasable. The Flash memory can be

programmed in four ways:

• In-Circuit Serial Programming™ (ICSP™)

• Run-Time Self-Programming (RTSP)

•JTAG

• Enhanced In-Circuit Serial Programming

(Enhanced ICSP)

ICSP allows a PIC24FJ256GA705 family device to be

serially programmed while in the end application circuit.

This is simply done with two lines for the programming

clock and programming data (named PGCx and PGDx,

respectively), and three other lines for power (VDD),

ground (VSS) and Master Clear (MCLR). This allows

customers to manufacture boards with unprogrammed

devices and then program the microcontroller just

before shipping the product. This also allows the most

recent firmware or a custom firmware to be

programmed.

RTSP is accomplished using TBLRD (Table Read) and

TBLWT (Table Write) instructions. With RTSP, the user

may write program memory data in blocks of

128 instructions (384 bytes) at a time and erase

program memory in blocks of 1024 instructions

(3072 bytes) at a time.

The device implements a 7-bit Error Correcting Code

(ECC). The NVM block contains a logic to write and

read ECC bits to and from the Flash memory. The

Flash is programmed at the same time as the

corresponding ECC parity bits. The ECC provides

improved resistance to Flash errors. ECC single bit

errors can be transparently corrected; ECC double-bit

errors result in a trap.

6.1

Table Instructions and Flash

Programming

Regardless of the method used, all programming of

Flash memory is done with the Table Read and Table

Write instructions. These allow direct read and write

access to the program memory space from the data

memory while the device is in normal operating mode.

The 24-bit target address in the program memory is

formed using the TBLPAG<7:0> bits and the Effective

Address (EA) from a W register, specified in the table

instruction, as shown in Figure 6-1.

The TBLRDL and the TBLWTL instructions are used to

read or write to bits<15:0> of program memory.

TBLRDL and TBLWTL can access program memory in

both Word and Byte modes.

The TBLRDH and TBLWTH instructions are used to read

or write to bits<23:16> of program memory. TBLRDH

and TBLWTH can also access program memory in Word

or Byte mode.

FIGURE 6-1:

ADDRESSING FOR TABLE REGISTERS

Note:

This data sheet summarizes the features of

this group of PIC24F devices. It is not

intended to be a comprehensive reference

source. For more information, refer to

the “dsPIC33/PIC24 Family Reference

Manual”,

“PIC24F

Flash

Program

Memory” (DS30009715), which is avail-

able

from

the

Microchip

website

(www.microchip.com). The information in

this

data

sheet

supersedes

the

information in the FRM.

Program Counter

24 Bits

Program

TBLPAG Reg

8 Bits

Working Reg EA

16 Bits

Using

Byte

24-Bit EA

1/0

Select

Table

Instruction

Counter

Using

User/Configuration

Space Select

DI35 데이터시트(PDF) 71 Page - Microchip Technology

DI35 데이터시트(HTML) 71 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL