 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
AS8501 데이터시트(PDF) 1 Page - ams AG |
|
|
|||||||||||||||||||||||||||||
AS8501 데이터시트(HTML) 1 Page - ams AG |
|
|
1 / 40 page  1.1 2 3 DATA SHEET Revision 1.1, 04-April-06 www.austriamicrosystems.com Page 1 of 40 1 Features 16 bits resolution Differential inputs Single + 5V supply Low power 15 mW SOIC16 package Self- and system-calibration with auto-calibration on power up 16 kHz maximum sampling frequency Internal temperature measurement Internal factory trimmed precision reference Programmable current sources Digital comparator Active wake-up PGA gains 1, 6, 24, 50, 100 Zero offset Zero offset TC Extremely low noise Internal oscillator with comparator for active wake up 3-wire serial interface, μP compatible Temperature range – 40 to + 125 °C Individual 24-bit serial number 2 Applications Battery management for automotive systems Power management mV/µV-meter High-precision voltage and current measurement 3 General description The AS8501 is a complete, low power data acquisition system for very small signals (i.e. voltages from shunt resistors, thermocouples) that operates on a single 5 V power supply. The chip powers up with a set of default conditions at which time it can be operated as a read-only-converter. Reprogramming is at any time possible by just writing into two internal registers via the serial interface. The AS8501 has four ground refering inputs which can be switched separately to the internal PGA. Two input channels can also be operated as a fully differential ground free input. The system can measure both positive and negative input signals. The PGA amplification ranges from 6 to 100 which enables the system to measure signals from 7mV to 120 mV full scale range with high accuracy, linearity and speed. The chip contains a high precision bandgap reference and an active offset compensation that makes the system offset free (better than 0,5 μV) and the offset-TC value negligible. The built- in programmable digital filter allows an effective noise suppression if the high speed is not necessary in the application. The input noise density is only 35 nV / Hz and due to the high internal chopping frequency the system is free of 1/f-noise down to DC.The 0-10 Hz noise is typical below 1 µV i.e. as good or better than any other available chopper amplifier. For high speed synchronous measurements the chip can run in an automatic switching mode between two input channels with pre- programmed parameter sets. The circuit has been optimised for the application in battery management systems in automotive systems. As a front end data acquisition system it allows an high quality measurement of current, voltage and temperature of the battery. With a high quality 100 μΩ resistor the system can handle the starter current of up to 1500 A, a continuous current of ± 300 A as well as the very low idle current of a few mA in the standby mode. For external temperature measurement the chip can use a wide variety of different temperature sensors such as RTD, PTC, NTC, thermocouples or even diodes or transistors. A built-in programmable current source can be switched to any input and activate these sensors without the need of other external components. The measurement of the chip temperature with the integrated internal temperature sensor allows in addition the temperature compensation of sensitive parameters which increases the total accuracy considerably. Sensor specific data can be stored in the internal Zener-Zap memory and are used to calibrate each measurement in the internal data processing unit before transmission to the external µC via the serial SDI interface. The flexibility of the system is further increased by a digital comparator that can be assigned to any measured property (current, voltage, temperature) and an active wake-up in the sleep-mode. All analog input-terminals can be checked for wire break via the SDI- interface. INTERNAL TEMPERATURE INPUT MUX CHOPPER PROTECTION CURRENT SOURCES ETR ETS RSHH RSHL VBAT 16 BIT - CONVERTER BUF SERIAL INTERFACE / CONTROL REGISTERS DSP CONTROLLER FILTER INT. CLOCK TIMER CALIBRATION DATA COMPARATOR 1.26 V REFERENCE SCLK SDAT INTN REF AGND VDDA VSSA VDDD VSSD CLK EZPRG PGA and LEVEL SHIFT AS8501 Preliminary Data Sheet High precision voltage and current measurement sensor interface Figure 1: Functional Block Diagram |
유사한 부품 번호 - AS8501 |
|
유사한 설명 - AS8501 |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
