SST26VF032BEUI datasheet(21/76 Pages) MICROCHIP

21 / 76 page

 2019 Microchip Technology Inc.

DS20006152A-page 21

SST26VF032BEUI

5.12

SPI Dual-Output Read

The SPI Dual-Output Read instruction supports fre-

quencies of up to 104 MHz from 2.7-3.6V and up to 80

MHz from 2.3-3.6V. Initiate SPI Dual-Output Read by

executing an 8-bit command, 3BH, followed by address

bits A[23-0] and a dummy byte. CE# must remain

active low for the duration of the SPI Dual-Output Read

operation. See Figure 5-13 for the SPI Quad Output

Read sequence.

Following the dummy byte, the SST26VF032BEUI out-

puts data from SIO[1:0] starting from the specified

address location. The device continually streams data

output through all addresses until terminated by a low-

to-high transition on CE#. The internal address pointer

automatically increments until the highest memory

address is reached, at which point the address pointer

returns to the beginning of the address space.

FIGURE 5-13:

FAST READ, DUAL-OUTPUT SEQUENCE

5.13

SPI Dual I/O Read

The SPI Dual I/O Read (SDIOR) instruction supports

up to 80 MHz frequency. Initiate SDIOR by executing

an 8-bit command, BBH. The device then switches to

2-bit I/O mode for address bits A[23-0], followed by the

Set Mode configuration bits M[7:0]. CE# must remain

active low for the duration of the SPI Dual I/O Read.

See Figure 5-14 for the SPI Dual I/O Read sequence.

Following the Set Mode configuration bits, the

SST26VF032BEUI outputs data from the specified

address location. The device continually streams data

output through all addresses until terminated by a low-

to-high transition on CE#. The internal address pointer

automatically increments until the highest memory

address is reached, at which point the address pointer

returns to the beginning of the address space.

The Set Mode Configuration bit M[7:0] indicates if the

next instruction cycle is another SPI Dual I/O Read

command. When M[7:0] = AXH, the device expects the

next continuous instruction to be another SDIOR com-

mand, BBH, and does not require the op-code to be

entered again. The host may set the next SDIOR cycle

by driving CE# low, then sending the two-bit wide input

for address A[23:0], followed by the Set Mode configu-

ration bits M[7:0]. After the Set Mode configuration bits,

the device outputs the data starting from the specified

address location. There are no restrictions on address

location access.

When M[7:0] is any value other than AXH, the device

expects the next instruction initiated to be a command

instruction. To reset/exit the Set Mode configuration,

execute the Reset Quad I/O command, FFH. See Fig-

ure 5-15 for the SPI Dual I/O Read sequence when

M[7:0] = AXH.

CE#

SIO0

SCK

012345678

31 32

MODE 3

MODE 0

15 16

3BH

20005218 F52.3

39 40 41

A[23:16]

A[15:8]

A[7:0]

b6 b5

SIO1

Address

OP Code

Data

Byte 0

Dummy

Data

Byte N

b3 b1

b7 b4

b2 b0

MSB

Note: MSB = Most Significant Bit.

SST26VF032BEUI 데이터시트(PDF) 21 Page - Microchip Technology

SST26VF032BEUI 데이터시트(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

데이터시트 다운로드

링크 URL