DRT

Solder Paste Stencil Opening

KSw

S

Q

4 mil 752 0.66

0.76

1.52 0.38

0.026 0.030 0.060 0.015

6 mil 752 0.051 0.064 1.40 0.30

0.020 0.025 0.055 0.012

34

35

SRT

Solder Paste Stencil Opening

KSw

S

Q

4 mil 752 2.40

0.76

0.38

0.095 0.030

NA

0.015

6 mil 752 1.90

0.63

0.33

0.075 0.025

NA

0.013

AB

C

D

742

1.80

0.80

0.50

0.90

0.071

0.032

0.020

0.035

743

1.90

1.27

0.80

1.20

0.075

0.050

0.032

0.047

744

3.00

1.27

0.80

1.30

0.118

0.050

0.032

0.051

745

3.00

1.27

0.80

1.30

0.118

0.050

0.032

0.051

746

1.52

0.64

0.35

0.80

0.060

0.025

0.014

0.032

Dimensions mm/inch

Series

Surface Mount Land Patter ns

Concave and Convex Chip Resistor Arrays 742-746

Surface Mount Series 752

Surface Mount Series 753

Surface Mount Series 766, 767 & 768

"D"

"C"

"B"

"A"

"C"

2.03

0.080

TYP.

1.27

0.050

TYP.

0.63

0.025

TYP.

"D"

"B"

"A"

Lead

AB

C

D

Count

766-8P

3.60

5.60

7.60

3.81

0.140

0.220

0.300

0.150

766-14P

3.60

5.60

7.60

7.60

0.140

0.220

0.300

0.300

766-16P

3.60

5.60

7.60

8.90

0.140

0.220

0.300

0.350

767-14

5.34

7.37

9.40

7.60

0.210

0.290

0.370

0.300

767-16

5.34

7.37

9.40

8.90

0.210

0.290

0.370

0.350

768-14

5.34

7.37

9.40

7.60

0.210

0.290

0.370

0.300

768-16

5.34

7.37

9.40

8.90

0.210

0.290

0.370

0.350

768-20

5.34

7.37

9.40

11.43

0.210

0.290

0.370

0.450

Concave/Convex

Stencil Opening

Stencil Opening

SRT

Solder Paste Stencil Opening

KSw

S

Q

4 mil 753 2.75

0.30

0.15

0.108 0.012

NA

0.006

6 mil 753 1.72

0.30

0.15

0.068 0.012

NA

0.006

Stencil Opening

DRT

Solder Paste Stencil Opening

KSw

S

Q

4 mil 753 0.51

0.30

1.32 0.15

0.020 0.012 0.052 0.006

6 mil 753 0.028 0.030 1.47 0.15

0.011 0.012 0.058 0.006

Stencil Opening

Land Patterns

No. of

“H” Dim

Pads

In.

mm

8

0.175

4.44

9

0.200

5.08

10

0.225

5.72

12

0.275

6.99

16

0.175

4.44

18

0.200

5.08

20

0.225

5.72

24

0.275

6.99

"B"

"C"

"A"

Keep out zone for stand offs.

Circuit board traces should be avoided

in this area to allow the stand off to rest

directly on the PCB.

"F"

"H"

SINGLE ROW

TERMINATION

"B"

"C"

"A"

"F"

DUAL ROW

TERMINATION

"E"

"D"

Dim.

In.

mm.

A

0.120

3.05

B

0.025

0.64

C

0.017

0.43

D

0.050

1.27

E

0.020

0.51

F

0.035

0.89

Land Patterns

No. of

“H” Dim

Pads

In.

mm

8

0.350

8.89

9

0.400

10.16

10

0.450

11.43

12

0.550

13.97

16

0.350

8.89

18

0.400

10.16

20

0.450

11.43

24

0.550

13.97

Dim.

In.

mm.

A

0.125

3.18

B

0.050

1.27

C

0.030

0.76

D

0.050

1.27

E

0.025

0.64

F

0.050

1.27

Solder Paste

Stencil Opening

"K"

"S"

Radius Q

Sw

"K"

Radius Q

Sw

NOTE:

s

Land Patterns for Concave and

Convex termination can be the same.

Series 752 & 753 Stencil Openings

Series 752 & 753 Land Patterns