LIS2DUXS12 datasheet(17/104 Pages) STMICROELECTRONICS

17 / 104 page

Table 10. Internal pin status

Pin #

Name

Function

Pin status

SCL

SPC

I²C/MIPI I3C® serial clock (SCL)

SPI serial port clock (SPC)

Default: input without pull-up

SPI/I²C/MIPI I3C® mode selection

1: SPI idle mode / I²C/MIPI I3C® enabled

0: SPI enabled / I²C/MIPI I3C® disabled

Default: input with internal

pull-up

SDO

SA0

Serial data output (SDO)

I²C less significant bit of the device address (SA0)

Default: input without

internal pull-up

SDA

SDI

SDO

I²C/MIPI I3C® serial data (SDA)

SPI serial data input (SDI)

3-wire interface serial data output (SDO)

Default: (SDA) input without

internal pull-up

Internally not connected. Can be tied to Vdd, Vdd_IO, or GND.

GND

0 V supply

RES

Connect to GND if not used as interrupt pin 1(1)

GND

0 V supply

Vdd

Power supply

Vdd_IO Power supply for I/O pins

INT2

Interrupt pin 2. Clock input when selected in one-shot mode. AH input 2 (or Qvar electrode 2) is

connected if the analog hub (or Qvar functionality) is enabled.(4)

Default: input with internal

pull-down(2)(3)

INT1

Interrupt pin 1. AH input 1 (or Qvar electrode 1) is connected if the analog hub (or Qvar

functionality) is enabled.(4)

Default: input with internal

pull-down(5)(6)

1. When the INT1_ON_RES bit of register CTRL1 (10h) is set to 1, the interrupt signals configured on the INT1 pin are routed to the RES pin.

This is useful when the analog hub / Qvar feature is enabled and the INT1 and INT2 pins are used to connect the external analog lines or

the electrodes to sense the Qvar signal.

2. The internal pull-down can be disconnected by setting the PD_DIS_INT2 bit of register PIN_CTRL (0Ch) to 1. When this is done, the INT2

pin needs to be externally biased.

3. The INT2 pin is configured as "push-pull output forced to GND" (and the internal pull-down disabled) as soon as it is configured with

the interrupt configuration bits in the CTRL3 (12h), MD2_CFG (20h), EMB_FUNC_INT2 (0Eh), FSM_INT2 (0Fh), and MLC_INT2 (11h)

registers.

4. The analog hub and Qvar functions are enabled by setting the AH_QVAR_EN bit to 1 in AH_QVAR_CFG (31h).

5. The internal pull-down can be disconnected by setting the PD_DIS_INT1 bit of register PIN_CTRL (0Ch) to 1. When this is done, the INT1

pin needs to be externally biased.

6. The INT1 pin is configured as "push-pull output forced to GND" (and the internal pull-down disabled) as soon as it is configured with

the interrupt configuration bits in the CTRL2 (11h), MD1_CFG (1Fh), EMB_FUNC_INT1 (0Ah), FSM_INT1 (0Bh), and MLC_INT1 (0Dh)

registers.

LIS2DUXS12

Application hints

DS14035 - Rev 2

page 17/104

LIS2DUXS12 데이터시트(PDF) 17 Page - STMicroelectronics

LIS2DUXS12 데이터시트(HTML) 17 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL