LPC2364 datasheet(30/48 Pages) PHILIPS

30 / 48 page

LPC2364_66_68_1

Preliminary data sheet

Rev. 01 — 22 September 2006

30 of 48

Philips Semiconductors

LPC2364/2366/2368

Fast communication chip

7.25 System control

7.25.1 Reset

Reset has four sources on the LPC2364/66/68: the RESET pin, the Watchdog Reset,

Power On Reset (POR) and the Brown Out Detection circuit (BOD). The RESET pin is a

Schmitt trigger input pin. Assertion of chip Reset by any source, once the operating

voltage attains a usable level, starts the Wake-up timer (see description in Section 7.24.3

“Wake-up timer”), causing reset to remain asserted until the external Reset is

de-asserted, the oscillator is running, a fixed number of clocks have passed, and the

Flash controller has completed its initialization.

When the internal Reset is removed, the processor begins executing at address 0, which

is initially the Reset vector mapped from the Boot Block. At that point, all of the processor

and peripheral registers have been initialized to predetermined values.

7.25.2 Brown-out detection

The LPC2364/66/68 includes 2-stage monitoring of the voltage on the VDD pins. If this

voltage falls below 2.95 V, the Brown-Out Detector (BOD) asserts an interrupt signal to

the Vectored Interrupt Controller. This signal can be enabled for interrupt in the Interrupt

Enable Register in the VIC in order to cause a CPU interrupt; if not, software can monitor

the signal by reading a dedicated status register.

The second stage of low-voltage detection asserts Reset to inactivate the LPC2364/66/68

when the voltage on the VDD pins falls below 2.65 V. This Reset prevents alteration of the

Flash as operation of the various elements of the chip would otherwise become unreliable

due to low voltage. The BOD circuit maintains this reset down below 1 V, at which point

the Power-On Reset circuitry maintains the overall Reset.

Both the 2.95 V and 2.65 V thresholds include some hysteresis. In normal operation, this

hysteresis allows the 2.95 V detection to reliably interrupt, or a regularly-executed event

loop to sense the condition.

7.25.3 Code security

This feature of the LPC2364/66/68 allows an application to control whether it can be

debugged or protected from observation.

If after reset the on-chip bootloader detects a valid checksum in flash and reads

0x8765 4321 from address 0x1FC in flash, debugging will be disabled and thus the code

in flash will be protected from observation. Once debugging is disabled, it can be enabled

by performing a full chip erase using the ISP.

7.25.4 AHB bus

The LPC2364/66/68 implements two AHB buses in order to allow the Ethernet block to

operate without interference caused by other system activity. The primary AHB, referred

to as AHB1, includes the Vectored Interrupt Controller, General Purpose DMA Controller,

USB interface, and a 8 kB SRAM primarily intended for use by the USB.

The second AHB, referred to as AHB2, includes only the Ethernet block and an

associated 16 kB SRAM. In addition, a bus bridge is provided that allows the secondary

AHB to be a bus master on AHB1, allowing expansion of Ethernet buffer space into

unused space in memory residing on AHB1.

LPC2364 데이터시트(PDF) 30 Page - NXP Semiconductors

LPC2364 데이터시트(HTML) 30 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

데이터시트 다운로드

링크 URL