전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

HC705C9AGRS/D 데이터시트(PDF) 88 Page - NXP Semiconductors

부품명 HC705C9AGRS/D
상세설명  General Release Specification
PDF  157 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NXP [NXP Semiconductors]
홈페이지  http://www.nxp.com
Logo NXP - NXP Semiconductors

HC705C9AGRS/D 데이터시트(HTML) 88 Page - NXP Semiconductors

Back Button HC705C9AGRS/D Datasheet HTML 84Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 85Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 86Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 87Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 88Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 89Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 90Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 91Page - NXP Semiconductors HC705C9AGRS/D Datasheet HTML 92Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 88 / 157 page
background image
General Release Specification
Start Bit Detection
MC68HC705C9A — Rev. 2.0
Serial Communications Interface (SCI)
9.12 Start Bit Detection
When the input (idle) line is detected low, it is tested for three more
sample times (referred to as the start edge verification samples in
Figure 9-4). If at least two of these three verification samples detect a
logic zero, a valid start bit has been detected; otherwise, the line is
assumed to be idle. A noise flag is set if all three verification samples do
not detect a logic zero. Thus, a valid start bit could be assumed with a
set noise flag present.
If a framing error has occurred without detection of a break (10 zeros for
8-bit format or 11 zeros for 9-bit format), the circuit continues to operate
as if there actually was a stop bit, and the start edge will be placed
artificially. The last bit received in the data shift register is inverted to a
logic one, and the three logic one start qualifiers (shown in Figure 9-4)
are forced into the sample shift register during the interval when
detection of a start bit is anticipated (see Figure 9-6); therefore, the start
bit will be accepted no sooner than it is anticipated.
If the receiver detects that a break (RDRF = 1, FE = 1, receiver data
register = $003B) produced the framing error, the start bit will not be
artificially induced and the receiver must actually detect a logic one
before the start bit can be recognized (see Figure 9-7).
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com