Micro-D Metal Shell - .050" Contact Spacing

MDM

Panel Cutouts

11

www.ittcannon.com

Dimensions shown in inch (mm)

Specifications and dimensions subject to change

++

++

++

++

Shell Sizes 9 thru 51

Shell Size 100

Figure 1

Front Mounting

D

TYP.

D

TYP.

B

C

C

A

A

B

.100

(2.54)

R TYP.

.450±.002

(11.43±0.05)

FULL R.

(TYP.)

C

.030 (0.76) TYP.

D

PANEL REF.

)

.118

(3.00

1.805

(45.85

.015 (0.38)

R. MAX (TYP.)

FULL R. (TYP.)

FULL R. (TYP.)

FULL R. (TYP.)

PANEL REF.

)

.118

(3.00

)

.118

(3.00

)

)

+.005

-.000

1.805

(45.85

)

1.805

(45.85

)

.125

(3.18

)

1.456

(36.98

)

+0.10

-0.00

.361

(9.17

)

1.520

(38.61

)

.401

(10.18

.450+_.002

(11.43+_0.05)

.030

(0.76) TYP.

)

.015 (0.38)R.

MAX.(TYP)

FULL R.

(TYP.)

FULL R. (TYP.)

26˚/27˚TYP

Figure 2

Rear Mounting

Figure 3

Edgeboard Mounting

Figure 1

Front Mounting

Figure 2

Rear Mounting

Figure 3

Edgeboard Mounting

NOTE: See page 13 for rear panel mounting configuration.

+0.13

-0.00

+.005

-.000

+0.13

-0.00

+.004

-.000

+0.10

-0.00

+.004

-.000

+.005

-.000

+0.13

-0.00

+0.10

-0.00

+.004

-.000

+0.10

-0.00

+.004

-.000

+.005

-.000

+0.13

-0.00

+.005

-.000

+0.13

-0.00

+.005

-.000

+0.13

-0.00

+.005

-.000

+0.13

-0.00

Shell

Size

Cutout

Figure

1

2

3

1

2

3

1

2

3

1

2

3

1

2

3

1

2

3

1

2

3

.408

.401

-

.558

.551

-

.708

.701

-

.808

.801

-

.958

.951

-

1.108

1.101

-

1.058

1.051

-

.271

.252

-

.271

.252

-

.271

.252

-

.271

.252

-

.271

.252

-

.271

.252

-

.315

.295

.570

.570

.570

.720

.720

.720

.870

.870

.870

.970

.970

.970

1.120

1.120

1.120

1.270

1.270

1.270

1.220

1.220

1.220

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

.089

9

15

21

25

31

37

51

A

+.004

-.000

B

+.004

-.000

C

+.005

-.000

D

+.005

-.000

For 9-51 Shell Sizes

NOTES:

1. Front panel mounting is the preferred mounting

method. Front panel mounting dimensions

(figure 1) will accommodate either #2-56 screws

or jackpost hardware.

2. Rear panel mount dimensions (figure 2) will

accommodate #2-56 screw hardware only.

When mounting the connector with rear panel

mount jackpost see the panel cut-out

dimensions.

3. Edgeboard mounting bracket (figure 3) uses #2-

56 screws. Dimension .450+/-.002 (11.43+/-

0.05) locates the MDM receptacle flush with the

end of the board.

For 100 Shell Size

NOTES:

1. Front mounting is the preferred mounting

method. Front panel mounting dimensions

(figure 1) will accommodate either #4-40 screws

or jackpost hardware.

2. Rear panel mount dimensions (figure 2) will

accommodate #4-40 screw hardware only see

the panel cut-out dimensions.

3.Edgeboard mounting bracket (figure 3) uses #4-

40 screws. Dimension .450+/-.002 (11.43+/-

0.05) locates the MDM receptacle flush with the

end of the board.