전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

PCA9420BS 데이터시트(PDF) 22 Page - NXP Semiconductors

부품명 PCA9420BS
상세설명  Power management IC for low-power microcontroller applications
PDF  85 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NXP [NXP Semiconductors]
홈페이지  http://www.nxp.com
Logo NXP - NXP Semiconductors

PCA9420BS 데이터시트(HTML) 22 Page - NXP Semiconductors

Back Button PCA9420BS Datasheet HTML 18Page - NXP Semiconductors PCA9420BS Datasheet HTML 19Page - NXP Semiconductors PCA9420BS Datasheet HTML 20Page - NXP Semiconductors PCA9420BS Datasheet HTML 21Page - NXP Semiconductors PCA9420BS Datasheet HTML 22Page - NXP Semiconductors PCA9420BS Datasheet HTML 23Page - NXP Semiconductors PCA9420BS Datasheet HTML 24Page - NXP Semiconductors PCA9420BS Datasheet HTML 25Page - NXP Semiconductors PCA9420BS Datasheet HTML 26Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 22 / 85 page
background image
NXP Semiconductors
PCA9420
Power management IC for low-power microcontroller applications
8.13.2 Battery temperature sensing and JEITA-compliant charging profile
aaa-049003
45°C
60°C
10°C
Programmed VBAT_REG
0°C
No operation
during cold fault
Programmed ICHG
(100%)
50%
Cold fault
0
0.2
VHOT VWARM
0.4
0.6
0.8
1.0
VCOOL
1.2
1.4
VCOLD
1.6
Termination
disable
1.8
TS voltage-V
Hot
fault
charge
disable
Figure 11. Operation over TS bias voltage for JEITA
Please refer to Section 8.6 for more details
8.13.3 Battery attach detection
The device has a unique battery detection scheme with two comparators, 1.9 V and 3.4 V. When the detection
scheme is executed, a 5 mA current sink is activated to determine battery presence by detecting the fall
threshold, VBAT_DET_LOW, 1.9 V typ. In addition, a 5 mA current source is used to detect battery voltage whether
it stays above the threshold, VBAT_DET_UP, 3.4 V. If both conditions are met, absence of battery is declared.
Battery detection sequence steps:
1. VBAT Sources 5 mA current to the PMIC Battery Detection Circuit.
2. If VBAT voltage is above 1.9 V, the battery is present. Stop the detect sequence, assert the “present” output.
3. Else if VBAT voltage is below 1.9 V, source 5 mA from PMIC into VBAT pin.
4. If VBAT voltage is below 3.4 V, the battery is present. Stop the detect sequence, assert the “present” output.
5. Else if VBAT voltage is above 3.4 V, the battery is absent (open). The charger stays disabled.
NOTE: The battery detect source and sink are separate dedicated circuits; 5 mA is a constant, not
programmable. The reset source is recorded on the "Reset monitor" register (address 0x71h)
For more details, see Figure 10.
8.13.4 Low-battery/dead-battery (pre-qualification) charging
If the battery is detected and VBAT < VBAT_LOW, the charger initiates pre-charging using a predefined (I2C
register) current.
PCA9420
All information provided in this document is subject to legal disclaimers.
© 2023 NXP B.V. All rights reserved.
Product data sheet
Rev. 4.2 — 26 July 2023
22 / 85



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com