| 전자부품 데이터시트 검색엔진 |
|
TPA2012D2RTJTG4 데이터시트(PDF) 12 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TPA2012D2RTJTG4 데이터시트(HTML) 12 Page - Texas Instruments |
|
12 / 20 page ![]() www.ti.com Decoupling Capacitor (C S) Input Capacitors (C I) fc + 1 2p R ICI (1) C I + 1 2p R I f c (2) TPA2012D2 SLOS438C – DECEMBER 2004 – REVISED MARCH 2007 The TPA2012D2 is a high-performance Class-D audio amplifier that requires adequate power supply decoupling to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients, spikes, or digital hash on the line a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1 µF, placed as close as possible to the device PV DD lead works best. Placing this decoupling capacitor close to the TPA2012D2 is important for the efficiency of the Class-D amplifier, because any resistance or inductance in the trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise signals, a 4.7 µF or greater capacitor placed near the audio power amplifier would also help, but it is not required in most applications because of the high PSRR of this device. Table 1. Gain Setting INPUT IMPEDANCE GAIN GAIN G1 G0 (RI) (V/V) (dB) (k Ω) 0 0 2 6 28.1 0 1 4 12 17.3 1 0 8 18 9.8 1 1 16 24 5.2 The TPA2012D2 does not require input coupling capacitors if the design uses a differential source that is biased from 0.5 V to VDD– 0.8 V. If the input signal is not biased within the recommended common-mode input range, if high pass filtering is needed (see Figure 34), or if using a single-ended source (see Figure 35), input coupling capacitors are required. The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in Equation 1. The value of the input capacitor is important to consider as it directly affects the bass (low frequency) performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the corner frequency can be set to block low frequencies in this application. Not using input capacitors can increase output offset. Equation 2 is used to solve for the input coupling capacitance. If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better, because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below. 12 Submit Documentation Feedback |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |