AT45DB321D_07 datasheet(16/55 Pages) ATMEL

16 / 55 page

3597H–DFLASH–02/07

AT45DB321D [Preliminary]

9.1.2

Program Sector Protection Register Command

Once the Sector Protection Register has been erased, it can be reprogrammed using the Pro-

gram Sector Protection Register command.

To program the Sector Protection Register, the CS pin must first be asserted and the appropri-

ate 4-byte opcode sequence must be clocked into the device via the SI pin. The 4-byte opcode

sequence must start with 3DH and be followed by 2AH, 7FH, and FCH. After the last bit of the

opcode sequence has been clocked into the device, the data for the contents of the Sector Pro-

tection Register must be clocked in. As described in Section 9.1, the Sector Protection Register

contains 64 bytes of data, so 64 bytes must be clocked into the device. The first byte of data cor-

responds to sector 0, the second byte corresponds to sector 1, and so on with the last byte of

data corresponding to sector 63.

After the last data byte has been clocked in, the CS pin must be deasserted to initiate the inter-

nally self-timed program cycle. The programming of the Sector Protection Register should take

place in a time of t

P, during which time the Status Register will indicate that the device is busy. If

the device is powered-down during the program cycle, then the contents of the Sector Protection

If the proper number of data bytes is not clocked in before the CS pin is deasserted, then the

protection status of the sectors corresponding to the bytes not clocked in can not be guaranteed.

For example, if only the first two bytes are clocked in instead of the complete 62 bytes, then the

protection status of the last 62 sectors cannot be guaranteed. Furthermore, if more than

64 bytes of data is clocked into the device, then the data will wrap back around to the beginning

of the register. For instance, if 65 bytes of data are clocked in, then the 65th byte will be stored at

byte location 0 of the Sector Protection Register.

If a value other than 00H or FFH is clocked into a byte location of the Sector Protection Register,

then the protection status of the sector corresponding to that byte location cannot be guaran-

teed. For example, if a value of 17H is clocked into byte location 2 of the Sector Protection

The Sector Protection Register can be reprogrammed while the sector protection enabled or dis-

abled. Being able to reprogram the Sector Protection Register with the sector protection enabled

allows the user to temporarily disable the sector protection to an individual sector rather than dis-

abling sector protection completely.

The Program Sector Protection Register command utilizes the internal SRAM buffer 1 for pro-

cessing. Therefore, the contents of the buffer 1 will be altered from its previous state when this

command is issued.

Figure 9-3.

Program Sector Protection Register

Command

Byte 1

Byte 2

Byte 3

Byte 4

Program Sector Protection Register

3DH

2AH

7FH

FCH

Data Byte

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

Data Byte

n + 1

Data Byte

n + 63

Each transition

represents 8 bits

AT45DB321D 데이터시트(PDF) 16 Page - ATMEL Corporation

AT45DB321D 데이터시트(HTML) 16 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

데이터시트 다운로드

링크 URL