AM29BL162C datasheet(14/52 Pages) AMD

14 / 52 page

Am29BL162C

22142F9 January 22, 2007

D A TA

SH EET

Burst Suspend/Burst Resume Operations

The device offers Burst Suspend and Burst Resume

operations. When both OE# and BAA# are taken high,

the device removes (“suspends”) the data from the

outputs (because OE# is high), but “holds” the data

internally. The device resumes burst operation when

either OE# and/or BAA# is asserted low. Asserting the

OE# only causes the device to present the same data

that was held during the Burst Suspend operation. As

long as BAA# is high, the device continues to output

that word of data. Asserting both OE# and BAA# low

resumes the burst operation, and on the next rising

edge of CLK, increments the counter and outputs the

next word of data.

IND# End of Burst Indicator

The IND# output signal goes low when the device is

outputting the last word of a 32-word burst sequence

(word Da+31). When the starting address was loaded

with LBA#, the 5-bit burst address counter was set to

00000b. The counter increments to 11111b on the

32nd word in the burst sequence. If the system con-

tinues to assert BAA# low, on the next CLK the device

outputs the starting address data (Da). The burst

address counter is again set to 00000b, and is

“wrapped around.”

Writing Commands/Command Sequences

To write a command or command sequence (which in-

cludes programming data to the device and erasing sec-

tors of memory), the system must drive WE# and CE# to

VIL, and OE# to VIH.

The device features an Unlock Bypass mode to facili-

tate faster programming. Once the device enters the Un-

lock Bypass mode, only two write cycles are required to

program a word, instead of four. The “Program Com-

mand Sequence” section has details on programming

data to the device using both standard and Unlock By-

pass command sequences.

An erase operation can erase one sector, multiple sec-

tors, or the entire device. Table 2 indicates the address

space that each sector occupies. A “sector address”

consists of the address bits required to uniquely select a

sector. The “Command Definitions” section has details

on erasing a sector or the entire chip, or suspending/re-

suming the erase operation.

After the system writes the autoselect command se-

quence, the device enters the autoselect mode. The sys-

tem can then read autoselect codes from the internal

DQ7–DQ0. Standard read cycle timings apply in this

mode. Refer to the “Autoselect Mode” and “Reset Com-

mand” sections for more information.

ICC2 in the DC Characteristics table represents the ac-

tive current specification for the write mode. The “AC

Characteristics” section contains timing specification ta-

bles and timing diagrams for write operations.

Program and Erase Operation Status

During an erase or program operation, the system may

check the status of the operation by reading the status

bits on DQ7–DQ0. Standard read cycle timings and ICC

read specifications apply. Refer to “Write Operation Sta-

tus” for more information, and to “AC Characteristics” for

timing diagrams.

Standby Mode

When the system is not reading or writing to the device,

it can place the device in the standby mode. In this

mode, current consumption is greatly reduced, and the

outputs are placed in the high impedance state, inde-

pendent of the OE# input.

The device enters the CMOS standby mode when the

CE# and RESET# pins are both held at VCC ± 0.3 V.

(Note: This is a more restricted voltage range than VIH.)

If CE# and RESET# are held at VIH, but not within VCC

± 0.3 V, the device is in the standby mode, but the

standby current is greater. The device requires standard

access time (tCE) for read access when the device is in

either of these standby modes, before it is ready to read

data.

If the device is deselected during erasure or program-

ming, the device draws active current until the operation

is completed.

In the DC Characteristics table, ICC3 and ICC4 represents

the standby current specification.

Automatic Sleep Mode

The automatic sleep mode minimizes Flash device

energy consumption. The device automatically enables

this mode when addresses remain stable for tACC + 30

ns. The automatic sleep mode is independent of the

CE#, WE#, and OE# control signals. Standard address

access timings provide new data when addresses are

changed. While in sleep mode, output data is latched

and always available to the system. ICC4 in the DC

Characteristics table represents the automatic sleep

mode current specification.

RESET#: Hardware Reset Pin

The RESET# pin provides a hardware method of reset-

ting the device to reading array data. When the system

drives the RESET# pin to VIL for at least a period of tRP,

the device immediately terminates any operation in

progress, tristates all data output pins, and ignores all

read/write attempts for the duration of the RESET#

pulse. The device also resets the internal state machine

to reading array data. The operation that was interrupted

should be reinitiated once the device is ready to accept

another command sequence, to ensure data integrity.

AM29BL162C 데이터시트(PDF) 14 Page - Advanced Micro Devices

AM29BL162C 데이터시트(HTML) 14 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

데이터시트 다운로드

링크 URL