| 전자부품 데이터시트 검색엔진 |
|
PCF8820 데이터시트(PDF) 17 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCF8820 데이터시트(HTML) 17 Page - NXP Semiconductors |
|
17 / 60 page ![]() 2000 Dec 07 17 Philips Semiconductors Product specification 67 × 101 Grey-scale/ECB colour dot matrix LCD driver PCF8820 7.18.5 I2C-BUS PROTOCOL The PCF8820 is a slave transmitter/receiver. If data is to be read from the device, the SDA_OUT output must be used. Before any data is transferred over the I2C-bus, the destination device is addressed first (see Fig.15). The PCF8820 has four 7-bit slave addresses reserved: 0111 100, 0111 101, 0111 110 and 0111 111. The two least significant bits of the slave address are set by connecting slave address inputs SA1 and SA0 to either VSS1 (logic 0) or VDD1 (logic 1). A write sequence (see Fig.17) is initiated with a START condition (S) from the I2C-bus master which is followed by the slave address. Only the addressed slave acknowledges. After acknowledgement, one or more command words follow which define the status of the addressed slave. A command word consists of a control byte (see Fig.16) defining ‘continuation’ bit Co and ‘register selection’ bit RS, plus a data byte. The last control byte is indicated by resetting bit Co = 0. The control and data bytes are also acknowledged by all addressed slaves on the bus. Depending on the setting of bit RS in the last control byte, either a series of display data bytes or command data bytes may follow. If bit RS = 1, the data bytes are stored as display data in the DDRAM at the address specified by the data pointer. The data pointer is automatically incremented. If bit RS = 0, the data byte is interpreted as a command byte to be decoded and the device will be set according to the received commands. Only the addressed PCF8820 acknowledges after each byte is received. The I2C-bus master issues a stop condition (P) at the end of the transmission. MGU185 S 01111 SA0 SA1 A slave address R/W acknowledge bit START condition slave address bit 1 read/write bit slave address bit 0 Fig.15 Slave address. MGT124 Co RS XXXXXX control byte register selection bit continuation bit Fig.16 Control byte. handbook, full pagewidth MGT125 S 01111 S A 0 S A 1 0A acknowledgement from PCF8820 acknowledgement from PCF8820 acknowledgement from PCF8820 acknowledgement from PCF8820 acknowledgement from PCF8820 1 control byte A data byte data byte m ≥ 0 bytes 1 byte slave address 2n ≥ 0 bytes A Co update data pointer Co 0A A P RS R/W control byte RS Fig.17 Write sequence: master transmits bytes to slave receiver. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |