MCR03

Resistors

Rev.D

2/5

Max. 50m

Ω

1A

−55°C to +155°C

Jumper type

Resistance

Rated current

Operating temperature

FX (

±1%)

J (

±5%)

D (

±0.5%)

10

≤ R ≤ 10M (E24,96)

(E24)

(E24)

±100

±400

1.0

≤ R ≤ 9.1

±200

10

≤ R ≤ 10M

(E24,96)

(E24,96)

10

≤ R ≤ 91

±100

±50

100

≤ R ≤ 1M

Table 1

Resistance tolerance

Resistance range

(

Ω)

Resistance temperature coefficient

(ppm/

°C)

Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

Characteristics

Item

Test conditions (JIS C 5201-1)

Resistor type

Guaranteed value

Jumper type

Resistance

Variation of resistance

with temperature

Solderability

Damp heat, steady state

Endurance at 70

°C

Endurance

Rapid change of

temperature

Bend strength of

the end face plating

Resistance to solvent

Resistance to

soldering heat

Overload

± (2.0%+0.1Ω)

Max. 50m

Ω

± (1.0%+0.05Ω)

± (3.0%+0.1Ω)

Max. 50m

Ω

Max. 100m

Ω

J :

±5%

FX :

±1%

D :

±0.5%

See Table.1

No remarkable abnormality on the appearance.

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Without mechanical damage such as breaks.

Max. 50m

Ω

JIS C 5201-1 4.5

JIS C 5201-1 4.8

Measurement :

−55 / +25 / +125°C

JIS C 5201-1 4.18

Soldering condition : 260

±5°C

Duration of immersion : 10

±1s.

JIS C 5201-1 4.24

40

°C, 93%RH

Test time : 1,000h to 1,048h

± (3.0%+0.1Ω)

± (3.0%+0.1Ω)

± (1.0%+0.05Ω)

± (1.0%+0.05Ω)

± (1.0%+0.05Ω)

Max. 100m

Ω

Max. 100m

Ω

Max. 50m

Ω

Max. 50m

Ω

Max. 50m

Ω

JIS C 5201-1 4.25.1

Rated voltage (current), 70

°C

1.5h : ON

− 0.5h : OFF

Test time : 1,000h to 1,048h

JIS C 5201-1 4.25.3

155

°C

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23

±5°C, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.19

Test temp. :

−55°C to +125°C 5cyc

JIS C 5201-1 4.33

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235

±5°C

Duration of immersion : 2.0

±0.5s.

JIS C 5201-1 4.13

Rated voltage (current)

×2.5, 2s.

Maximum overload voltage : 100V