 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
SP6685ER 데이터시트(PDF) 11 Page - Sipex Corporation |
|
|
|||||||||||||||||||||||||||||
SP6685ER 데이터시트(HTML) 11 Page - Sipex Corporation |
|
|
11 / 16 page  11 Date: 7/6/06 Rev B SP6685, 700mA Buck/BoostCharge Pump LED Driver © 2006 Sipex Corporation FUNCTIONAL DIAGRAM THEORY OF OPERATION RSET BLOCK 6 RSET RSET V= {1.26V RSET } x11.2kohms + - 1.26V + - BG REF RSET REF RESISTOR TAPS 50mV 4 FLASH FLASH=1, S=1, RSET REF FLASH=0, S=0, 50mV 1 0 s MUX 2x1 FB REF 7 FB SGN 8 FB COM P + - FB COMP CLR COUNTER 32 COUNT ONE SHOT SET DOMINANT S R 0 MODE SWITCH 0 =1X 1=2X 1 5 EN VIN 135C ON 145C OFF THERMAL FAULT OVER TEMP COMP CLK CLK 2.4MHZ CHARGE PUMP SWITCHES PGND C1 C2 VOUT CLK SP6685 auto detects a dropout condition, which is when the FB pin is below the regulation point for more than 32 cycles of the internal clock, the SP6685 automati- cally switches to the 2X mode. The SP6685 remains in the 2X mode until one of four things happens: 1) the enable pin EN has been toggled, 2) the Flash pin has changed from high to low, 3) V IN is cycled or, 4) a thermal fault occurs. The 2X mode is the charge pump mode where the output can be pumped as high as two times the input voltage, provided the output does not exceed the maximum volt- age for the SP6685, which is internally limited to about 5.5V. In the 2X mode, as in the 1X mode, the output current is regulated by the voltage at the FB pin. In the Torch mode, (Flash = GND) the Flash pin is set to logic low and the SP6685 FB pin regulates to 50mV output: V FB = 50mV (Torch Mode) The SP6685 is a charge pump regulator designed for converting a Li-Ion battery voltage of 2.7V to 4.2V to drive a white LED used in digital still camera Flash and Torch applications. The SP6685 has two modes of operation which are pin selectable for either Flash or Torch. Flash mode is usually used with a pulse of about 200 to 300 milliseconds to generate a high intensity Flash. Torch can be used continuously at a lower output current than Flash and is often used for several seconds in a digital still camera “movie” mode. The SP6685 also has two modes of opera- tion to control the output current: the 1X mode and 2X mode. Operation begins after the enable pin EN receives a logic high, the bandgap reference wakes up after 200μsec, and then SP6685 goes through a soft-start mode designed to reduce inrush current. The SP6685 starts in the 1X mode, which acts like a linear regulator to control the output current by continuously monitoring the feedback pin FB. In 1X mode, if the |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
