전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

SP6691EK/TR 데이터시트(PDF) 9 Page - Sipex Corporation

부품명 SP6691EK/TR
상세설명  SOT23Micro Power Boost Regulator Series White LED Driver
PDF  15 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  SIPEX [Sipex Corporation]
홈페이지  http://www.sipex.com
Logo SIPEX - Sipex Corporation

SP6691EK/TR 데이터시트(HTML) 9 Page - Sipex Corporation

Back Button SP6691EK/TR Datasheet HTML 5Page - Sipex Corporation SP6691EK/TR Datasheet HTML 6Page - Sipex Corporation SP6691EK/TR Datasheet HTML 7Page - Sipex Corporation SP6691EK/TR Datasheet HTML 8Page - Sipex Corporation SP6691EK/TR Datasheet HTML 9Page - Sipex Corporation SP6691EK/TR Datasheet HTML 10Page - Sipex Corporation SP6691EK/TR Datasheet HTML 11Page - Sipex Corporation SP6691EK/TR Datasheet HTML 12Page - Sipex Corporation SP6691EK/TR Datasheet HTML 13Page - Sipex Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 15 page
background image

Jun26-07 Rev D
Micro Power Boost Regulator Series White LED Driver
© 2007 Sipex Corporation
Output Voltage Program
The SP6691 can be programmed as either a
voltage source or a current source. To program
the SP6691 as voltage source, the SP6691 re-
quires 2 feedback resistors R1 & R2 to control
the output voltage. As shown in Figure 22.
Table 4. Divider Resistor Selection
Brightness Control
Dimming control can be achieved by applying a
PWM control signal to the SHDN pin. The
brightness of the white LEDs is controlled by
increasing and decreasing the duty cycle of the
PWM signal. A 0% duty cycle corresponds to
zero LED current and a 100% duty cycle corre-
sponds to full load current. While the operating
frequency range of the PWM control is from
60Hz to 700Hz, the recommended maximum
brightness frequency range of the PWM signal
is from 60Hz to 200Hz. A repetition rate of at
least 60Hz is required to prevent flicker. The
magnitude of the PWM signal should be higher
than the minimum SHDN voltage high.
Open Circuit Protection
When any white LED inside the white LED
module fails or the LED module is disconnected
from the circuit, the output and the feedback
control will be open, thus resulting in a high
output voltage, which may cause the SW pin
voltage to exceed it maximum rating. In this
case, a zener diode can be used at the output to
limit the voltage on the SW pin and protect the
part. The zener voltage should be larger than the
maximum forward voltage of the White LED
module.
APPLICATION INFORMATION: Continued
L1
1.22V
R2
D1
C1
C2
R1
VOUT
U1
SP6691
1
2
3
4
5
SW
G ND
FB
SHDN
V
IN
VIN
Figure 22. Using SP6691 as Voltage Source
The formula and table for the resistor selection
are shown below:
R1 =
( VOUT - 1 ) • R2
1.22
precision resistors are recommended. Table 3
below shows the Rb selection for different white
LED currents. For example, to set the operating
current to be 20mA, Rb is selected as 60.4 , as
shown in the schematic.
Table 3. Bias Resistor Selection
IF (mA)
Rb ( )
5
243
10
121
12
102
15
80.6
20
60.4
VOUT (V)
R1 ( )
R2 ( )
12
1M
113K
15
1M
88.7K
18
1M
73.2K
21
1M
61.9K
30
1M
42.2K



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com